Top tips for maintaining an evaporative cooler

Evaporative coolers, also known as swamp coolers have become a top choice for anyone looking for an alternative cooling solution from their home or office. In the past, evap cooler technology was limited for use in large operations that have easy access to exterior air such as factories.

The technology has grown leaps and bounds over the last decade and now portable units that have all the features of standard air-condition..., such as; thermostats, large LCD displays and even remote control management.

Apart from all these added features have enabled evap coolers to become a superior choice over traditional air-conditioners, evap cooler technology has now been compacted into smaller units that suit the home and office.

How do they work?

Evaporative cooler harness the power of nature, in particular the cooling effect of evaporation. Have you ever been relaxing by a lake and felt a cool breeze come across the surface and land on shore to refresh you? This is the principle that is behind evaporative cooling. As warm air passes over or through a body of water, there is a latent heat exchange that occurs as the water is evaporated by the warm air, pushing the warmth into the water and cooling the air.

This process is harnessed by an evaporative cooler by means of a fan that is housed within the unit pulling warm ait from outside into the unit and through a set of cooling pads that are constantly wetted. The air then undergoes the latent heat exchange and the fresh, cool air is then pushed into the room where it cools the ambient temperature.

The working parts

Evaporative coolers are inexpensive to operate and they can offer a power saving of up to 70% when compared with other traditional air-conditioning systems. This is because there are very few electrical components within the evaporative cooler unit. Inside the unit, you will find a thermostat to control the operation of the cooler, as well as a water pump that pushes water over the cooling pads and an electric fan to pull in the warm air and expel the cool air.

The evap cooler difference

Being that evaporative coolers require less energy to operate, they also have a unique method of operation in order for the unit to operate at its full, efficient capacity. In traditional air-con systems, you are required to seal the room that needs cooling by closing all the doors and windows and then go about consistently remediating and cooling the rooms air. Evaporative coolers work by forcing new, freshly cooled air into the room, therefore they require an exhaust point in order for the old, spent air to be expelled from the room as the new air replaces it.

Therefore, you will need to open a window or leave a door slightly open in order for the exhaust air to escape. Should you fail to open a window and create the negative pressure that is needed fo the air to escape, the room will slowly increase in relative humidity to the point where the rooms surfaces begin to become damp and them wet. This may destroy wooden furniture and window frames as well as damage electrical equipment and other household items such as painting, books and carpets.

Maintaining your cooler

In an ideal world, we would never have to lift a finger to do anything. Food would magically appear before us when dinnertime is near and our teeth would brush themselves in the morning. Obviously, these things will never happen there is a certain level of energy that must be spent in order to receive a reward, this is life.

The same principle applies to your evaporative cooler. In an ideal world, we would simply turn the unit on and it would run for the entire summer with no hassles. However, things are not this easy in life and your evaporative cooler will require some minor maintenance in order to keep it running at optimum efficiency.

2 steps to evap cooler success

While your evaporative cooler only requires a minimal amount of maintenance, it’s still important to make sure that you do the following;

The housing

Before the relentless heat of the summer arrives, it’s time to do a quick check up on your cooler. Begin by removing the weather cover and giving the external housing a quick check over for signs of cracking around the reservoir or fan grids. Make sure that the fan grid ids clean and free from debris such as dust or leaves.

Pump, pads and filter

Next, remove the housing to expose the reservoir, water pump, cooling pads and fan. Clean out the reservoir and make sure all sediment that could possibly clog up the water pump is removed, wipe down the reservoir and then turn on the unit to make sure that the reservoir fills and that the water pump is functioning correctly, pushing the water over the cooling pads. Next, turn the unit off again and remove the cooling pads and the filter. Wash them with a light soapy solution and then rinse them clean with fresh water before reinstalling them into the unit.

The fan

Check the fan impellers for signs of wear and then wipe them down to remove any dust or debris. Give the impeller a quick turn or two to make sure the bearing are working correctly and then spray them down with a silicone based lubricant.

Thermostat and electrical circuits

Next, make sure that the reservoir is filled with fresh water and switch on the unit for a test run. Use your control panel or remote control and turn on the unit. Make sure that the temperature settings are working and other electronic features such as the fan swing are functioning correctly.

The final check

For the final step, reassemble the housing and make sure that it is fitted securely, then give the unit a wipe down to remove any dirt, duct or debris that may have collected in storage or out in the open during the winter months, you are now ready to operate your unit!

At the end of the season

At the end of the summer season, after days of effective and efficient cooling, it’s time to pack your unit away. Empty the reservoir and clean the air-inlet grille and fan impellers. Then reassemble the unit and cover it with a weather cover if it is an exterior mounted unit, or a plastic cover to prevent dust build up if it is a smaller portable unit that you can store in your garage or cupboard.

What if something goes wrong?

If you discover a fault with anything on the list, then call your manufacturer or agent and arrange a technician to come out to your property to service the unit. For external units, you may have to have a call-out, however, if you have a lighter, portable unit, then just pop it into your car and take a drive to your agent where they can give it a service for you.

 

Who supplies Evaporative Coolers?

Depending on the country you’re situated in there are some great options for evaporative coolers. Below is a list of the top 5 evaporative cooler suppliers we have found. We have tried to split these out Geographically:  

www.essickair.com

www.evaporative-coolers.co.za

www.air-n-water.com

www.uline.com

www.ecer.com

 

The final thought

While machines such as evaporative coolers are built to improve our quality of life, they still need some TLC in order for them to run at their optimum efficiency and effectiveness. There is no thing as a free lunch and completing these few simple steps before turning on your unit will greatly extend its operating life, providing you with further maintenance savings alongside the dramatic electricity savings that you can expect from an evaporative cooler.

Views: 176

Tags: air, airconditioning, conditioning, cooler, coolers, evap, evaporative, portable, reviews, swamp

Comment

You need to be a member of Home Energy Pros Forum to add comments!

Join Home Energy Pros Forum

Forum Discussions

Too many Heat Pump Water Heaters in a basement?

Started by Brad Cook in General Forum. Last reply by David Butler 23 hours ago. 9 Replies

How would you insulate this roof?

Started by David Butler in General Forum. Last reply by David Butler yesterday. 2 Replies

Dirty solar panels

Started by Evan Mills in General Forum. Last reply by Stacie Bagnasco yesterday. 1 Reply

Fixing a water heater?

Started by John Shillito in Best Practices. Last reply by Eric Kjelshus on Friday. 21 Replies

Latest Activity

Profile IconSarah Burger, Troy Spindler, Mike Berg and 3 more joined Home Energy Pros Forum
2 hours ago
David Butler replied to Brad Cook's discussion Too many Heat Pump Water Heaters in a basement?
"theoretically, let's say you perfectly isolate the HPWH from a heat source. The HPWH's…"
23 hours ago
David Butler replied to David Butler's discussion How would you insulate this roof?
"Interesting idea. Commercial roof on a slope! Typical density for roofing spray foam is 2.5 to 3.0…"
yesterday
Summer Redman added a discussion to the group Job Board
Thumbnail

Hiring 2 Training Specialists in Champaign-Urbana, Illinois

The Applied Research Institute (ARI) at the University of Illinois at Urbana-Champaign is seeking…See More
yesterday
Summer Redman joined Diane Chojnowski's group
Thumbnail

Job Board

This group is for posting jobs related to all aspects of the home performance industry including…See More
yesterday
Profile IconJeff Farlow, John Hatfield, Crystal McLain and 5 more joined Home Energy Pros Forum
yesterday
Stacie Bagnasco replied to Evan Mills's discussion Dirty solar panels
"This is a great idea. I clicked on your discussion because it made me remember that I forgot to get…"
yesterday
Kirsten Richnavsky posted an event
Thumbnail

rCloud - The Future of Testing at Your Office or Home

October 18, 2017 from 2pm to 3pm
Integrating rCloud as an essential part of your RESNET QA process.Retrotec’s rCloud app is here,…See More
yesterday

Photos

Loading…
  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service