Rock Wool Insulation for Floor of High Performance Tiny House

VIDEO: Foundation and Floor Framing for High Performance Tiny House...

In August of 2016, we posted a video describing the design and construction of the foundation and floor framing of our High Performance Tiny House in Florida. Since then, we have made a lot of progress. We've also prioritized the design and construction of an off-grid, "zombie proof" homestead, and its permaculture farm, in the mountains of North Carolina, which kept us from sharing our experiences and shedding our knowledge on the blog! Alas, here is an update. Welcome to today's post!

WHERE WE LEFT OFF AT THE TINY HOUSE...

Whether you're seeing the video for the first time, or not, you heard me talk about insulating both the cavities and continuously on the outside of the sheathing. What I hope you picked up on, in the video, is that to achieve that continuity with the sheathing, we built the floor in sections, and upside down.

If we had set the floor joists on the masonry foundation wall, first, the sheathing would have been interrupted by the double sill plates on top of the masonry. This detail would have been much more complicated to deal with, but still doable.

By keeping the sheathing continuous, on the outside of the structure, we maintain continuity of our control layers, which gives us a "perfect" enclosure. And, by having continuous insulation, that has the appropriate hygrothermic (drying potential) and thermal properties, on the outside of the sheathing, we've protected the structure from exposure to the elements. This helps prevent LOTS of things that cause building failure (e.g. Rot, Mold, Freeze, Thaw, etc.), not to mention keeps us comfortable inside the house (This is a very good thing).

Image 1: Perfect Building Enclosure - Continuity is an absolute necessity to maintain a perfect enclosure.

ROCK WOOL INSULATION WORKS FOR FRAMED FLOOR, WALL AND ROOF/CEILING.

I've mentioned before why I like building with rocks. While it's not practical to use rocks for everything in the structure of the home, rocks could be the best ways to insulate. From the drying potential, as illustrated in the video below, and described in this blog post from July 2016, to the R-Value that increases as the temperature drops, to the fact that rocks don't burn, there are fewer and fewer reasons to NOT insulate with rocks.

VIDEO: ROXUL Comfortboard Drying Potential

After finishing the floor framing, we were ready for insulation. We started by insulating the cavities with 6" Batts (R-26.4 max at colder temperatures), and then installed the continuous 2" rigid (R-8.8 max at colder temperatures) rock wool insulation on the outside of the sheathing. As I mention in the "perfect enclosure" blog post, the walls and the roof were insulated the exact same way. Four (4") to six (6") inches of cavity insulation, with two (2) inches of continuous rigid insulation on the outside.

In a later post, I will explain the many reasons why using ONLY continuous exterior rigid insulation, with absolutely NO batt insulation in the cavities, is absolutely the most effective and simple way to insulate a building. HANDS DOWN. For now, we'll talk about using rock wool insulation batts in the cavities, too.

Here are pics from the installing the rock wool insulation batts and rigid board, before, during and after, at the High Performance Tiny House (Florida).

Image 2: 6" (TH) x 16" (W) x 48" (L) batts, with R-Value of 26.4 (at colder temperatures) were used in the floor and roof/ceiling cavities. We installed 4" batts, with R-Value of 17.6 (at colder temperatures), in the wall cavities.

Image 3: Rock wool insulation batts are unfaced, and maintain rigidity well when not handled more than necessary.

Image 4: Making sure there are absolutely no gaps or compression when installing insulation batts must be done, without exception, to achieve the maximum thermal resistance potential, and to maintain durability of the assembly. Gaps between the insulation and framing, or between individual batts, can lead to trapping or passage of unwanted moisture, as well as decreased thermal performance. Where the batt meets the sheathing is one of the most challenging, because you can't see it. But, that doesn't mean it can't be done right. Follow instructions!

Image 5: Carefully setting each batt in each cavity.

Image 6: Installing the batts vertically against the rim joist, will maintain continuity of the thermal layer with the exterior wall that will be built directly above. Continuity is KING! Trimming the insulation is done easily with an insulation knife, or in this case, a hacksaw.

Image 7: Leaving 1/4" to 3/8" of insulation above the top of the joist will ensure that the insulation will remain in contact with the subfloor sheathing, without reducing R-Value through compression.

Image 8: Looking down at the cantilevered corner of the framed floor. The vertical insulation continues around the perimeter of the structure.

Image 9: The batts are friction fit in to each cavity, and make a nice "blanket" of woven rocks.

Image 10: Because the joists are 2x10, there will be a gap between the top of the insulation and the bottom of the sub-floor. This works because continuous air, vapor and thermal control layers (sheathing and insulation) are outside of the bottom of the joists, instead of on top. This gap was not allowed in earlier building codes, but is now acceptable because it's understood to perform very well. This gap is within the thermal envelope, and part of the conditioned space.

Image 11: Continuous two-inch (2") rigid rock wool insulation on the outside of the continuous sheathing that's attached to the bottom of the floor joists, which is an all-in-one air, vapor and water control layer (ZIP System Sheathing). The insulation completes the assembly's critical control layers, by controlling heat (thermal). On the other side (top) of the continuous sheathing is where the rock wool insulation batts are installed (see Images 2 - 10).

For more on designing and building high performance homes, whether they're tiny or "zombie proof", be sure to read more of this blog, and follow along.

Thank you,

Chris Laumer-Giddens

Views: 277

Tags: high, house, insulation, mineral, performance, rock, tiny, wool

Comment

You need to be a member of Home Energy Pros Forum to add comments!

Join Home Energy Pros Forum

Comment by Safe-R Insulation on September 23, 2017 at 6:04am

Thanks for sharing this much information about roof wall insulation.


http://www.saferinsulation.co.nz/

Forum Discussions

Efficiency of furnace

Started by Jignesh in General Forum. Last reply by Eric Kjelshus 5 hours ago. 6 Replies

Insulation Blower Recommendations?

Started by Jim Conlon in General Forum. Last reply by Cameron Home Insulation 5 hours ago. 2 Replies

2005 EPAct tax credit

Started by Mandy Leazenby in General Forum. Last reply by Sean Lintow Sr on Thursday. 3 Replies

Best brands for furnace

Started by Jignesh in General Forum on Tuesday. 0 Replies

Latest Activity

Eric Kjelshus replied to Jignesh's discussion Efficiency of furnace
"I like looking at system efficiency - Lets say the you have a 95% gas using furnace 100,000…"
5 hours ago
Cameron Home Insulation replied to Jim Conlon's discussion Insulation Blower Recommendations?
"Hi, Rent a Cellulose Insulation Blower from your local Home Depot. Get more information about…"
5 hours ago
Todd Abercrombie liked Barbara Smith's video
yesterday
Jim Hensen replied to Jignesh's discussion Efficiency of furnace
"Great question - what the efficiency rating means is one of the most common questions we we asked.…"
yesterday
Michael Schettine's blog post was featured

Framing production combined with air sealing

Building Tighter Homes with Gasketed FramingIf you follow our blog, you know that we talk quite a…See More
Friday
Profile IconMichael E and Jason Dion joined Home Energy Pros Forum
Friday
Jason Dion joined Sean Lintow Sr's group
Thumbnail

Best Practices (Residential)

Best Building, Retrofitting, or even Auditing Practices - what are they, what should change, what…See More
Friday
Jason Dion joined Michael Stuart's group
Thumbnail

INFRARED THERMOGRAPHY USERS

This group is dedicated to knowledge sharing and discussion of infrared thermography for building…See More
Friday
Jason Dion joined allen p tanner's group
Thumbnail

Energy Auditing Equipment for Sale, Trade or to Purchase

Discuss the pros and cons of the equipment you are interested in prior to purchase. Post equipment…See More
Friday
Jason Dion joined Allison A. Bailes III's group
Thumbnail

HVAC

HVAC design, Manuals J, S, T, & D, Duct leakage, Air flow, ENERGY STAR new home requirements,…See More
Friday
Jason Dion joined Bob Krell's group
Thumbnail

Healthy Indoors (IAQ)

The Healthy Indoors group is focused on indoor air quality (IAQ), mold, moisture control, radon,…See More
Friday
Jason Dion joined Building Performance Institute's group
Thumbnail

Building Performance Institute (BPI)

BPI is the nation's premier standards development, quality assurance and credentialing organization…See More
Friday
Jason Dion joined Diane Chojnowski's group
Thumbnail

Job Board

This group is for posting jobs related to all aspects of the home performance industry including…See More
Friday
Brad Cook replied to Jignesh's discussion Efficiency of furnace
"NO combustion based heating system can ever be 100% efficient, according to the Second Law of…"
Thursday
Brian Robinson commented on Barbara Smith's video
Thumbnail

How to get top performance from your furnace, air conditioner or heat pump

"So glad you highlighted the importance of air sealing & insulating the home form the bottom to…"
Thursday
Brian Robinson replied to Jignesh's discussion Efficiency of furnace
"You also may also want to account for the distribution losses as you move the heat from the…"
Thursday
Michael Schettine posted a blog post

Framing production combined with air sealing

Building Tighter Homes with Gasketed FramingIf you follow our blog, you know that we talk quite a…See More
Thursday
David Butler replied to Jignesh's discussion Efficiency of furnace
"Adding to Sean's comment... The reason a 90%+ furnace uses a PVC flue (as opposed to metal) is…"
Thursday
Barbara Smith's video was featured

How to get top performance from your furnace, air conditioner or heat pump

Video produced as part of our Minnesota heating and cooling system study. Seventhwave
Thursday
DesignTech posted photos
Thursday

Photos

  • Add Photos
  • View All

© 2018   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service