For as long as I can remember, the agreed epidemic with ductwork was always undersized return ducts.  Although we are far from perfect with duct sizing in New England, I have frequently seen great strides in fixing this issue - particularly with replacement systems.  Lets face it, you should just be properly designing the duct system on new installations.  Undersized ducts cause great restrictions in airlfow, raising static pressure and lowering the cubic feet per minute (CFM).  Or, with ECM motors, raising the amperage draw above full load.  More recently, I continue to find efforts with regards to sizing, but other rules of duct design being ignored.  I am going to concentrate on one particular rule that can have the same affect as undersized ducts:

  • On supply and return, when the trunk is wider than the plenum, a transition fitting must be used!

Fig.1  No Transition: Filter Box

   Lack of transitions create turbulence and restrictions in your duct system.  Even if the Return Duct is large enough for your desired CFM, abrupt changes in sizes without a tapered transition raises static pressure drastically above design.  Take Figure 1 for example.  Imagine the force needed to pull the same volume of air through the nice IAQ Filter installed.  At least the entire filter area is being used! I frequently find larger filter boxes than the air handler opening, a waste of filter area - but at least less of a restriction.

Fig. 2 Return Drop

  Figure 2 is an all too common mistake on replacement system, when installing a high performance filter in basement systems.  The new filter box pushes the return drop out of the range of connecting to the trunk, without an offset transition.  Most tin-knockers will do what they can to get the furnace operating.  Following this up by cutting in a grille in the return drop to either fix the undersized ducts, or lack of a transition, is not going to work when it comes to air-conditioning!  The air must come from the conditioned space in order to remove the latent heat, not from a moisture laden basement...

  Can anyone tell me what is going on in Figure 3???  I hope this wasn't you!

http://excessair.blogspot.com/2014/07/please-make-transition.html

Fig. 3 Supply Transition(s)?

Views: 198

Comment

You need to be a member of Home Energy Pros Forum to add comments!

Join Home Energy Pros Forum

Latest Activity

David Byrnes's blog post was featured

Strategies for Hiring and Interviewing for Home Performance Professionals

Hire slow and fire fast.  It’s a phrase that experienced managers and human resources professionals…See More
22 minutes ago
Diane Chojnowski replied to David Butler's discussion Beginners Guide: Managing Subscriptions on Home Energy Pros
"Thanks for your comprehensive guide, David! There is an RSS feed you can subscribe to at the…"
41 minutes ago
Dara Bowser replied to Don Fugler's discussion joining ducts in the group HVAC
"Good to hear you have clean dryer ducts Don. The dryer duct issues that we run into are…"
16 hours ago
Don Fugler replied to Don Fugler's discussion joining ducts in the group HVAC
"David, If the IMC mandates metal dryer duct and prohibits metal screws, they must be accepting…"
17 hours ago
David Butler replied to Don Fugler's discussion joining ducts in the group HVAC
"I never checked that before. Checking now... Section M1502.4.2 of the International Residential…"
17 hours ago
Joseph Frasier is now a member of Home Energy Pros Forum
17 hours ago
Don Fugler replied to Don Fugler's discussion joining ducts in the group HVAC
"Brendan, Thanks for that response. Because of your warning, I just went down to the basement and…"
21 hours ago
Brendan Reid replied to Don Fugler's discussion joining ducts in the group HVAC
"Hi Don, Summary: DRYER VENT: screws bad idea, possibly prohibited by code. METAL DUCT: must be…"
22 hours ago

Photos

  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service