Framing production combined with air sealing

Building Tighter Homes with Gasketed Framing

If you follow our blog, you know that we talk quite a bit about building science. In fact, we wrote a primer on how builders can use building science to produce more durable, comfortable, and energy-efficient homes. We also share information on effective air sealing and blower door testing -- a pain point for some builders having to meet new testing requirements of the 2012 and 2015 Residential IECC.

As any building scientist worth their salt will tell you, air tight homes start with great framing. Michael Schettine of AccuFrame Energy Seal isn’t a building scientist, but he has more than 45 years’ experience in home building, carpentry, and architectural reconstruction. His background has led him to believe that there’s a better way to reach air tightness targets, and it begins with a positive change in the way homes are framed.

Frame It Better

One recent estimate pegs the failure rate of blower door tests at 40 to 50 percent. Because buildings must be largely completed before initial tests, builders get one shot at achieving air tightness targets like 3 ACH50 in climate zones 5 and 6. If the building doesn’t pass, it can be costly and time-consuming to rework, reschedule and retest.

“I’m hearing that builders are using cases and cases of caulk for air sealing and trades still have to come back because they’re not passing the blower door test. That’s a problem,” says Schettine. He revealed that builders can spend as much as $300 per home for standard caulking products and still may have additional costs because of a failed blower door test. He argues the best way to a pain-proof system is to air seal during framing.

“Builders don’t know they’re often about $200 away from solving this problem of multiple testing, reworking, and rescheduling compliance audits,” he said. By incorporating a framing gasket into the exterior wall during framing, builders can drastically reduce air infiltration and build a better-sealed home. The home will pass a blower door test the first time and be durable enough for the homeowner to realize lower energy cost while increasing comfort.

“Sealing needs to be done during framing for the best performance,” he said. “Sealing gaskets in between the framing will not only result in a tighter, more durable home but will also avoid the number one problem you see with caulking and framing–shrinkage once it dries.”

How It Works

 

 

With the framing lumber ready, the gasket product (preprinted with framing stud locations marked on a liner) is applied to the top and bottom plates (see video). Then the wall section studs are installed and aligned according to the framing guide printed on the product. The liner is then peeled off, and the edges of the gasket are adhered to the edges of the plates. The double top plate is then nailed to the component, and the exterior sheathing is nailed to the assembly, completing the wall installation.

According to New York State Energy Research and Development Authority – which partnered on a project with Schettine, the framing gasket helps improve energy performance. By creating a four-way seal between the horizontal plates, face of the frame, and back side of the sheathing, the framing gasket reduces air flow through the assembly. When subjected to ASTM E283 testing, the product proved to reduce air intrusion through the assembly by more than 81 percent. 

“With traditional framing and pressurization of the building due to heat/cooling cycles, air penetrates through any gap and connection point that’s not sealed,” he said. “Air sealing has to be continuous or else it’s ineffective. If you don’t have that continuous seal, air is pushed inward at the bottom-oriented strand board (OSB) and face-frame allowing air intrusion into the insulation cavity.  During a wind event, this will cause energy loss and problems like ice damming where the loss occurs at the top plates and underside roof deck.”

Schettine provided test results from two identical houses in New York State as a comparison. One was built with AccuFrame Energy Seal. The other house was built using a comprehensive interior caulking method that resulted in a blower door of 3.81 ACH50. Both houses used fiberglass insulation and the OSB was taped. A weather resistant barrier was sealed on to the outside shell as well. The gasket-framed house, with no further interior air sealing or caulking, on the other hand, resulted in a 2.63 ACH 50 blower door test reading. Schettine’s final result was a more durable solution with a 30 percent reduction of air intrusion over caulking.

Changing Practices Through Training

Schettine believes framing gaskets are appealing to builders because the superior air sealing capability allows them to use cost-effective fiberglass insulation paired with the product to achieve a superior result. “Air sealing is the most critical component of the insulation job and is the key to an air tight home. Building Science Corporation conducted a study that shows all insulation performers equally well when properly air sealed.  With this product, we’re stopping air from entering the OSB backside and the frame when other products are attempting to seal from the inside only. You have to stop air from entering the cavity and insulation to make a more air-tight assembly.”

But what would it take for this new approach to reach critical mass?

“All it takes to scale this approach is workforce knowledge and development. You must train framers in the new approach, but they’re willing to learn, and I’m starting to see traction from training schools. They’re teaching framers how to eliminate errors, increase productivity, and drive energy performance, and that’s where it all starts,” Schettine said.

The best part? It’s not cost prohibitive, according to Schettine and once the frame is complete, so is your air sealing detail.

“Building to the passive house standard beginning at $225 per square foot range is cost-prohibitive for most buyers, Schettine noted. “However, the gasket sealing approach allows mass builders of affordable homes to reduce cost and scheduling. The largest beneficiaries of switching to the gasket approach are the builders already using spraying foam, which is especially appealing to production builders dealing with tight budgets. And it delivers a return on investment for both builders and buyers by providing a more durable, long-lasting energy-efficient home.”

This article was originally posted on the Insulation Institute's Blog.

Views: 67

Tags: Energy, air, framing, gaskets, performance, production, sealing

Comment

You need to be a member of Home Energy Pros Forum to add comments!

Join Home Energy Pros Forum

Forum Discussions

Mini split installation location

Started by Jan Green in HVAC. Last reply by David Butler yesterday. 13 Replies

Think of the house as a really big duct

Started by Frank Spevak in HVAC. Last reply by John White on Friday. 2 Replies

Mini split air conditioners and ceiling fans

Started by Beverly Lerch in General Forum. Last reply by Beverly Lerch on Thursday. 13 Replies

Condensation on ceiling and walls of master bedroom

Started by Jerry Needham in General Forum. Last reply by John Nicholas on Thursday. 10 Replies

Latest Activity

Profile IconDavid R Young, Chris Joiner, mosan and 1 more joined Home Energy Pros Forum
14 hours ago
Home Performance Coalition liked Hannah Finch's blog post Announcing National Energy Geek Day [October 6]
15 hours ago
Tom Phillips replied to Don Fugler's discussion Choosing a range hood in the group Kitchen Ventilation
"thx, Don. See slides 16-17 BTW, it is a modeling study , based lab data and assumed outdoor PM2.5…"
19 hours ago
Matt Wright added a discussion to the group Job Board
Thumbnail

Home Performance Expert in Frisco, CO

Deeper Green ConsultingHome Performance ExpertJob Description:Deeper Green Consulting is seeking a…See More
20 hours ago
Home Performance Coalition shared Barbara Smith's video on Twitter
20 hours ago
Shine Facility Services posted a photo
20 hours ago
Don Fugler replied to Don Fugler's discussion Choosing a range hood in the group Kitchen Ventilation
"There is a scientific paper that Tom Phillips cited where the researchers are looking at the…"
21 hours ago
David Byrnes's video was featured

Should the Attic Floor Insulation Be Removed When Doing Spray Foam?

Spray foam insulation contractors and homeowners alike have debated this questions over many years and since spray foam first gained popularity
yesterday
John White posted a blog post
yesterday
David Butler replied to Jan Green's discussion Mini split installation location
"I'm not sure if I'm making myself clear. You don't want to 'squeeze' the…"
yesterday
Jim Gunshinan posted a blog post

More "Buzz" from ACEEE Summer Study—Grow Homes

Joe Clark and Martha Wudka of Evergreen Economics did a study in which "getting into the weeds (or…See More
yesterday
Jan Green replied to Jan Green's discussion Mini split installation location
"I agre that the south wall would be shaded for the warmer summer months, but it won't look…"
yesterday
Jan Green replied to Jan Green's discussion Mini split installation location
"I'll check on electrical.  Good point.  "
yesterday
Jan Green replied to Jan Green's discussion Mini split installation location
"Thank you for that.  I wanted to put it on the west wall since there isn't much chance of…"
yesterday
David Butler replied to Jan Green's discussion Mini split installation location
"Hi Jan, actually, I said you'd be find putting it on the west wall since you wanted a larger…"
yesterday
Brett Little posted an event
Thumbnail

Using Pearl Certification to Bridge the gap between home energy and value - Free CE Webinar at Webinar Online

October 3, 2018 from 12pm to 1:15pm
In this webinar, “The Power of the Pearl Connection”, Pearl Certification’s Cynthia Adams, CEO and…See More
yesterday
Walter Ahlgrim replied to Jan Green's discussion Mini split installation location
"Being a Flip you must consider the install cost. At least get a bid for a PTAC unit like the ones…"
yesterday
Daniel Baur-McGuire replied to Jan Green's discussion Mini split installation location
"South Wall. It will have the highest load needed for cooling/heating. the shade from the tree could…"
yesterday
Glen Gallo replied to Jan Green's discussion Mini split installation location
"I would add where is the power coming from? the south wall proposed might have easier access for…"
yesterday
Todd Hensel is now a member of Home Energy Pros Forum
yesterday

Photos

  • Add Photos
  • View All

© 2018   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service