Seems pretty elementary doesn't it?  What should be a simple safety check on fossil fuel burning appliances, particularly for boilers with regards to ease of inspection, often is assumed with complacency or even goes unchecked.  I know everyone's maintenance schedule is packing up in the Northeast with the cold snap this week, so Technicians Take Heed!

There are many indicators that should trigger the phrase: "Check the flue!"  I always measure the draft in the flue of a natural draft, 80% appliance.   Too high or too low of a draft both can be an issue.  HVAC Contractors tend to focus on the 'too little draft' by installing chimney liners, completing Combustion Appliance Zone and CO testing.  Of course this condition could be the most dangerous, so I can't blame them.  Who ever expects to pull the flue off the boiler, look into the chimney and see what is pictured?  There must have been 40 years of garbage piled up!  Really is a spectacular thing that after all the years of maintenance I have yet  to become complacent with the Flue. 

Did you know the draft of the chimney is very dependent on the temperature difference between the flue gas and outside.  The greater the temperature difference, the better the draft (generally speaking).  This means the draft may be just fine on a cold WInter night, yet spill gases on a warm Fall afternoon.  Conversion warning: 25 Pascals = .10" w.c.  I know: metric, really?...Trust me, the rest of the world has the real gripe when they see standard measurements.  I bet your electronic manometers or even magnahelics (whatever you are using for draft measurements) have this scale.  Take a look at this chart supplied by Building Performance Institute (T_Out is your Outdoor Ambient Temp), start testing, and be sure that boiler will be safe all year long.  Oh, and don't forget about the water heater too!

 

 

BPI.org

The draft was just fine on this older, larger than most boilers (-.03"w.c.).  Except how long before that chimney became a real problem?  I have to tell everyone: I have found birds, nests, even a squirrel in a 90%+ flue.  Yes, that was a rotting mess to cut through with a hacksaw in a half-finished basement.  Always test the draft, measure the CO, and look into the flue/chimney.  You may just be surprised one day; possibly save someone, or maybe a home!

http://excessair.blogspot.com/2013/09/check-flue.html

Views: 2341

Comment

You need to be a member of Home Energy Pros Forum to add comments!

Join Home Energy Pros Forum

Comment by Bob Blanchette on October 8, 2013 at 7:46pm

ALL dryers should have the duct checked annually. Electric dryers will set the lint on fire if the heating element doesn't burn out first.

Comment by Dennis Heidner on October 8, 2013 at 6:23pm

Good article..

If the homes have a natural gas dryer - check the flue -- in this case the vent line is as important.  Long drying times are symptons of a clogged dryer vent... and when its natural gas -- that means the flue is not operating efficiently.  

Forum Discussions

How would you insulate this roof?

Started by David Butler in General Forum. Last reply by David Butler 2 hours ago. 34 Replies

Psychrometric Chart Training

Started by John Krochmalny in Training. Last reply by Mahendra Shah on Friday. 1 Reply

Dirty solar panels

Started by Evan Mills in General Forum. Last reply by Stacie Bagnasco Oct 16. 1 Reply

Latest Activity

David Butler replied to David Butler's discussion How would you insulate this roof?
"Sean Lintow proposed rails and clips (re: first comment in this discussion), but in the context of…"
2 hours ago
Brad Cook replied to David Butler's discussion How would you insulate this roof?
"I missed where the suggestion for rails came in. The plywood would not need any rails. 4+ inches is…"
6 hours ago
David Butler replied to David Butler's discussion How would you insulate this roof?
"I'm a little confused about the necessity and purpose of using support rails if working on…"
7 hours ago
David Butler replied to David Butler's discussion How would you insulate this roof?
"If you insulate master bedroom and family room from below, you definitely need more R-value than…"
7 hours ago
David Butler replied to David Butler's discussion How would you insulate this roof?
"Brad, I was only talking about using EPS between the ridges, if necessary, to conform to bolts.…"
7 hours ago
Brad Cook replied to David Butler's discussion How would you insulate this roof?
"It kind of depends on the PIC. Not all insulation is made the same. Here in VT (and all of New…"
7 hours ago
David Butler replied to David Butler's discussion How would you insulate this roof?
"Filling those shallow valleys with rigid foam not only prevents primary foam panels from…"
8 hours ago
Brad Cook replied to David Butler's discussion How would you insulate this roof?
"Bill, you just posted a number of responses in different areas of the thread. I will try to respond…"
12 hours ago

Photos

  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service