TJ Ewing
  • Male
  • Maple City, MI
  • United States
Share on Facebook Share
  • Blogs
  • Discussions
  • Events
  • Groups (11)
  • Photos
  • Photo Albums
  • Videos

TJ Ewing's Friends

  • Elizabeth Russell
  • allen p tanner
  • Steven Lewis
  • Fluke Thermal Imaging
  • Michael Stuart
  • Judi Lyall
  • Chris Laumer-Giddens
  • John Nicholas
  • Allison A. Bailes III
 

TJ Ewing's Page

Profile Information

Company
Empowerment Energy Analysts
Professional Certification
CEA (AEE), LEED GA, RESNET HERS Rater, Level 1 Thermographer, BPI Building Analyst, BPI Envelope Professional
Professional Interests
Building Science, energy conservation, efficiency, thermography, Passive House construction, measurement & verification, education.
Website URL
http://empowermentenergy.com
Twitter ID
EmpowermentEng

Comment Wall (2 comments)

You need to be a member of Home Energy Pros Forum to add comments!

Join Home Energy Pros Forum

At 12:43pm on November 21, 2010, allen p tanner said…
TJ I took my 'block wall IR' training from unitedinfrared.com. If you want to go this route; as for Peter and tell him I said to give you the BPI courtesy discount.
Any way; the theory is that the sun needs to heat the wall, (solar loasding), sufficiently to allow the cooler cores to show the Delta T needed. Similar to flat roof scanning where we can locate moisture under a roof membrane and prior to interior ceiling damage.
You will need to take scans at different intervals and camera settings through out the day. This way you can compare images and capture the best anomalie. The color setting usuallly works best in IRON Bow or similar. You will also have to adjust the camera range at 20 degrees from high to low.
That is why interior IR doesn't work as well. The masonry wall will be more uniform through out unless there is a major moisture leak or perhaps heating duct break in the wall. I would suggest going out side and scanning some block walls at different times to get a feel for it. The sun hits different wallls at different levels so more than 1 wall cn be tested.
At 10:05am on November 21, 2010, allen p tanner said…
How are you progressing on your 'wall scan"?
One comment on the continuous running furnace fan; did the customer put the fan on 'run' instead of auto? Is the furnice an older moel that has a blower control thermostat in the hot air plenum that controls the fan and is defective?
It will cost energy to continuously run the blower and could cause excessive wear and tear and failure.
 
 
 

Forum Discussions

Psychrometric Chart Training

Started by John Krochmalny in Training 9 hours ago. 0 Replies

Too many Heat Pump Water Heaters in a basement?

Started by Brad Cook in General Forum. Last reply by Michael Duclos 14 hours ago. 10 Replies

How would you insulate this roof?

Started by David Butler in General Forum. Last reply by David Butler on Monday. 2 Replies

Dirty solar panels

Started by Evan Mills in General Forum. Last reply by Stacie Bagnasco on Monday. 1 Reply

Latest Activity

B Eric Bell liked Bob Krell's group Healthy Indoors (IAQ)
6 hours ago
John Krochmalny posted a discussion

Psychrometric Chart Training

Looking through the various areas of this site, I didn't see too much information or training on…See More
9 hours ago
Profile IconMike Malek, Avery T. Phillips and Sarah Burger joined Home Energy Pros Forum
10 hours ago
Dannie Jackson's blog post was featured

Core Heat And Other Concepts

  In some places the use of solar heated liquids from hot water solar panels are used to provide…See More
14 hours ago
Michael Duclos replied to Brad Cook's discussion Too many Heat Pump Water Heaters in a basement?
"I’ve been looking into Sanden for a multi-family PH near Laconia, NH, ASHRAE 99.6% temp is…"
14 hours ago
Profile IconTroy Spindler, Mike Berg, Andrew McDowell and 4 more joined Home Energy Pros Forum
yesterday
David Butler replied to Brad Cook's discussion Too many Heat Pump Water Heaters in a basement?
"theoretically, let's say you perfectly isolate the HPWH from a heat source. The HPWH's…"
Monday
David Butler replied to David Butler's discussion How would you insulate this roof?
"Interesting idea. Commercial roof on a slope! Typical density for roofing spray foam is 2.5 to 3.0…"
Monday

Photos

Loading…
  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service