Greetings everyone,

   I have a strange scenario to model and I was hoping I could get some advice: This used to be a whole building built on 1,920 so it is a balloon framing. The homeowner' s apartment is on the second floor, but the front door on the first floor has a little area with a little "receiving" table and that area is heated with a radiator. The basement ceiling has no insulation at all and because of the framing style, it brings a great deal of air into the 2 floor (proved by the blower door) 

   The entire house is two floors plus attic, but I am modeling a little piece of the first floor, second floor, attic and basement... Any suggestions on how to do this?

  Your comments are greatly appreciated,

                              Luis

Views: 172

Replies to This Discussion

Paul, Good Evening, John here, did you ever get an answer from anyone to this question?  I am fairly new to TREAT but I am willing to discuss this if it still matters to you?

John@jwlasso.co.uk

Boy, Luis, sorry to see this so late.

Curious what you did.  Our general approach would be to model only the surfaces in the apartment  that are adjacent to unconditioned space, so leaving off floors and walls that are adjacent to the neighboring apartments.

What approach did you use?

Ethan 

RSS

Discussion Forum

Basic Heat loss information

Started by Luis Hernandez. Last reply by tedkidd Oct 30, 2014. 1 Reply

How to model a skylight

Started by Luis Hernandez. Last reply by Luis Hernandez Oct 16, 2014. 2 Replies

Modeling the apartment upstairs

Started by Luis Hernandez. Last reply by Ethan MacCormick Sep 26, 2014. 2 Replies

Modeling a Townhouse

Started by Luis Hernandez. Last reply by Luis Hernandez Jul 7, 2013. 4 Replies

Latest Activity

Brett Little posted an event
Thumbnail

Green Rater LEED Credential Online Training at Online

September 5, 2018 at 12pm to September 6, 2018 at 5pm
With over 450,000 LEED® for Homes™ spaces worldwide, LEED is the international rating system to…See More
11 hours ago
Michael Schettine commented on Michael Schettine's video
Thumbnail

AccuFrame Water Test

"The Like button doesn't work on this site..."
23 hours ago
Franco Oyuela commented on Mike Muras's blog post "Practical Standards to Measure HVAC System Performance" Rob "Doc" Falke 04/17/2006
"It's important to evaluate and inspect a system regularly to make sure it's at optimal…"
yesterday
Seventhwave posted an event

HVAC technology enhancements for energy conservation at The Marq

October 4, 2018 from 8:30am to 4pm
Join us to learn how to get the largest energy savings in your commercial buildings. HVAC as a…See More
yesterday
Peter Krych replied to Dav Camras's discussion Adding blown insulation to poorly installed batts?
"I agree, it is wasteful to remove and dump old insulation. I still does its job. Air sealing is…"
yesterday
Michael Schettine commented on Michael Schettine's video
Thumbnail

AccuFrame Water Test

"With the conversion rate that- air is 800 time LESS dense than water at sea-level…"
yesterday
Michael Schettine posted a video

AccuFrame Water Test

In this short video, water is used to visualize air leakage sites that are present in the majority of framed walls in the US. New regulations require better ...
yesterday
Sam Feder liked Dav Camras's discussion Adding blown insulation to poorly installed batts?
Thursday
Chris Stratton liked Don Fugler's discussion Choosing a range hood
Thursday
Dave Taylor replied to Jerry Needham's discussion VERY TIGHT HOME WITH OVER SIZED AC
"Jerry, you should look at Buildingscience.com" High Mass Walls" 105 paper for more…"
Thursday
Jill Lindman's 3 events were featured
Thursday
Jill Lindman posted events
Thursday
Diane Chojnowski posted videos
Thursday
Don Fugler replied to Don Fugler's discussion Choosing a range hood in the group Kitchen Ventilation
"Has anyone installed a range hood in an older home with the ducting down to the basement and out…"
Thursday
Profile IconEileen Kraus-Dobratz, VENI MITTAL and Mark A McCrumb joined Home Energy Pros Forum
Thursday
Brian Robinson replied to Dav Camras's discussion Adding blown insulation to poorly installed batts?
"YES, YES, & YES!!! Bat droppings, mouse droppings, dead mice, nuts, seeds, acorns, lack of…"
Wednesday
Matt Peterson posted a blog post

The Importance of keeping Professionally Trained Gas Line Installation Technicians happy and loving their jobs!

Our company is very much a family to us, we strive to bring in and develop great people into great…See More
Wednesday
Profile Iconyanky fogel, Kathleen Krebs, Nicholas Rubenstein and 3 more joined Home Energy Pros Forum
Wednesday
yanky fogel liked Home Energy Magazine's video
Tuesday
Franco Oyuela commented on Shawn Weeks's blog post How Homeowners Can Keep Electricity Costs Down in Summer Months
"Cutting back on air conditioning is also good for the environment because it reduces carbon…"
Tuesday

Photos

  • Add Photos
  • View All

© 2018   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service