TREAT Software Discussions (11)

← Back to TREAT Software
Discussions Replies Latest Activity

Distribution Efficiency and heating safety factor in TREAT

Greetings everyone,      I was wondering if anyone could help me with this error, TREAT is saying that the primary heating system capacity…

Started by Luis Hernandez

2 Oct 30, 2014
Reply by tedkidd

Basic Heat loss information

Greetings everyone,      I was told that I could get very basic heating loss calculations from TREAT. Besides the amount of fuel usage I c…

Started by Luis Hernandez

1 Oct 30, 2014
Reply by tedkidd

How to model a skylight

Skylights have different criteria than windows under NYSERDA protocols, so I am trying to figured out how to model a skylight!!! Any help w…

Started by Luis Hernandez

2 Oct 16, 2014
Reply by Luis Hernandez

Modeling the apartment upstairs

Greetings everyone,    I have a strange scenario to model and I was hoping I could get some advice: This used to be a whole building built…

Started by Luis Hernandez

2 Sep 26, 2014
Reply by Ethan MacCormick

Modeling a Townhouse

Hi everyone!       I am learning TREAT, so perhaps this is too simple of a question for you guys but I am kind of stuck... when TREAT asked…

Started by Luis Hernandez

4 Jul 7, 2013
Reply by Luis Hernandez

Modeling attics slopes for foam.

How are attic slopes modeled for foam insulation. When ever I've added a foamed slope I get a very low SIR with virtually no savings. What…

Started by Paul Lasicki

4 Aug 23, 2012
Reply by tedkidd

Improvement Question

A client has an old gas fired boiler with a gas fired storage tank DHW. I'm looking to replace both units with a high efficiency gas fired…

Started by Paul Lasicki

5 Mar 21, 2012
Reply by randy tolowski

line volt(age) thermostats

Comment by Jan E. Graveamkeron ThursdayDelete Comment Electric baseboard or electric in wall (can) heaters, is there a way in TREAT to repl…

Started by Jan E. Graveamker

1 Feb 27, 2012
Reply by Amber Harris

Treat descriptions

Hi, Is it possible to add preferences in the drop down menus for surface descriptions. Example, when I go to a 2x8 framing there is nothing…

Started by Paul Lasicki

1 Feb 27, 2012
Reply by Amber Harris

Truing up

With the latest On Bill financing, we are require to use actual fuel usage in TREAT. I tried a couple of times to use actual usage or tried…

Started by Paul Lasicki

4 Feb 16, 2012
Reply by Paul Lasicki

RSS

Discussion Forum

Basic Heat loss information

Started by Luis Hernandez. Last reply by tedkidd Oct 30, 2014. 1 Reply

How to model a skylight

Started by Luis Hernandez. Last reply by Luis Hernandez Oct 16, 2014. 2 Replies

Modeling the apartment upstairs

Started by Luis Hernandez. Last reply by Ethan MacCormick Sep 26, 2014. 2 Replies

Modeling a Townhouse

Started by Luis Hernandez. Last reply by Luis Hernandez Jul 7, 2013. 4 Replies

Latest Activity

Dara Bowser replied to Don Fugler's discussion joining ducts in the group HVAC
"Good to hear you have clean dryer ducts Don. The dryer duct issues that we run into are…"
14 hours ago
Don Fugler replied to Don Fugler's discussion joining ducts in the group HVAC
"David, If the IMC mandates metal dryer duct and prohibits metal screws, they must be accepting…"
15 hours ago
David Butler replied to Don Fugler's discussion joining ducts in the group HVAC
"I never checked that before. Checking now... Section M1502.4.2 of the International Residential…"
15 hours ago
Joseph Frasier is now a member of Home Energy Pros Forum
15 hours ago
Don Fugler replied to Don Fugler's discussion joining ducts in the group HVAC
"Brendan, Thanks for that response. Because of your warning, I just went down to the basement and…"
19 hours ago
Brendan Reid replied to Don Fugler's discussion joining ducts in the group HVAC
"Hi Don, Summary: DRYER VENT: screws bad idea, possibly prohibited by code. METAL DUCT: must be…"
20 hours ago
Profile IconBrendan Reid and David Butler joined Allison A. Bailes III's group
Thumbnail

HVAC

HVAC design, Manuals J, S, T, & D, Duct leakage, Air flow, ENERGY STAR new home requirements,…See More
20 hours ago
Profile IconSean Wiens and David Butler joined Chris Laumer-Giddens's group
Thumbnail

Energy Efficient Design

Energy efficiency starts at the drafting table...How architects and designers can help buildings…See More
yesterday

Photos

  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service