Blower Door Tests
The tool for inducing pressures and measuring air leakage in buildings. Shows the sources of the leaks with the help of artificial smoke.

See Greg Thomas: “So You Want to be a Home Performance Contractor”
Home Energy, Home Performance Special Issue, 2006

These are some reasons for establishing the proper building tightness:

* Reducing energy consumption due to air leakage
* Avoiding moisture condensation problems
* Avoiding uncomfortable drafts caused by cold air leaking in from the outdoors
* Making sure that the home's air quality is not too contaminated by indoor air pollution.

How They Work

A blower door is a powerful fan that mounts into the frame of an exterior door. The fan pulls air out of the house, lowering the air pressure inside. The higher outside air pressure then flows in through all unsealed cracks and openings. The auditors may use a smoke pencil to detect air leaks. These tests determine the air infiltration rate of a building.

Blower doors consist of a frame and flexible panel that fit in a doorway, a variable-speed fan, a pressure gauge to measure the pressure differences inside and outside the home, and an airflow manometer and hoses for measuring airflow.


There are two types of blower doors: calibrated and uncalibrated. It is important that auditors use a calibrated door. This type of blower door has several gauges that measure the amount of air pulled out of the house by the fan. Uncalibrated blower doors can only locate leaks in homes. They provide no method for determining the overall tightness of a building. The calibrated blower door's data allow the auditor to quantify the amount of air leakage and the effectiveness of any air-sealing job.

Take the following steps to prepare your home for a blower door test:

* Close windows and open interior doors
* Turn down the thermostats on heaters and water heaters
* Cover ashes in wood stoves and fireplaces with damp newspapers
* Shut fireplace dampers, fireplace doors, and wood stove air intakes.

Source: U.S. Department of Energy - Energy Savers

See "PFT Air Infiltration Measurement Technique"
Source: U.S. Department of Energy - Energy Savers

Views: 77

Replies to This Discussion

I like seeing the white Blower Door fan with the white blades.  This tells me that this is an old work horse that has been around for at least 15 years.

RSS

Discussion Forum

Seeking a Flow Hood

Started by George Matthews Apr 10. 0 Replies

Affordable Manometers?

Started by Isaac Savage. Last reply by Pete Stoermer Feb 15, 2016. 3 Replies

Looking For A Retrotech Duct Tester ?

Started by Chris Schiewer. Last reply by Jamie Kaye Dec 16, 2015. 1 Reply

Buying Used Equipment

Started by Nick Semon May 18, 2015. 0 Replies

Used Blower Doors?

Started by Isaac Savage. Last reply by Cameron Millard Jan 16, 2014. 3 Replies

Latest Activity

Mike Rogers posted a discussion

Home Energy Pros and #MeToo

If it doesn't seem obvious why a discussion of …See More
1 hour ago
Profile IconCharles Buell, Robert Cowell, Alice Quinn and 1 more joined Home Energy Pros Forum
7 hours ago
David Butler replied to David Butler's discussion How would you insulate this roof?
"Sean Lintow proposed rails and clips (re: first comment in this discussion), but in the context of…"
15 hours ago
Brad Cook replied to David Butler's discussion How would you insulate this roof?
"I missed where the suggestion for rails came in. The plywood would not need any rails. 4+ inches is…"
20 hours ago
David Butler replied to David Butler's discussion How would you insulate this roof?
"I'm a little confused about the necessity and purpose of using support rails if working on…"
20 hours ago
David Butler replied to David Butler's discussion How would you insulate this roof?
"If you insulate master bedroom and family room from below, you definitely need more R-value than…"
20 hours ago
David Butler replied to David Butler's discussion How would you insulate this roof?
"Brad, I was only talking about using EPS between the ridges, if necessary, to conform to bolts.…"
20 hours ago
Brad Cook replied to David Butler's discussion How would you insulate this roof?
"It kind of depends on the PIC. Not all insulation is made the same. Here in VT (and all of New…"
20 hours ago

Photos

  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service