Tags: air-sealing, cantilever

Views: 926

Replies to This Discussion

found this "vented cantilever"  -- the builder used the same vented soffit in the cantilevered 1st floor that is used for the roof eaves.  There was just a little unfaced FG stuffed in first but I pulled that aside to see a pretty much air cooled space between the main floor and the finished basement on the windy west side of this home.  I reinstalled R19 faced FG, cut blue board to fit between the 2x4's and foamed all the edges and joints before re-installing the soffit -- much warmer at the living room bay window. -- Oh yes, I stuck caulk backer - foam strips in between the top of the brick and the 2 by framing also.

I'll bet a nickel that 99 out of 100 of these that you come across will be the same condition.  One I found had a suspended ceiling in the basement, even more gross.

Awesome post Kari, thanks for sharing. Look at that discoloration!

+1 to Stan's post, though his number might be low, 9999 out of 10,000? After all, even if they wanted to do better and knew how, the work would put them at competitive disadvantage. So there is no compelling counterbalance to NMEB (not my energy bill), or reason to cure building science ignorance.

You have before and after blower door numbers and home sf? Love to know how much that tightened things up.

I like the NMEB acronym -- I'm going to use that again.  I'll have to look for the pre & post BD nos.(It's been more than a year since I ran the post)  This home had a kitchen soffit open to the attic with 7 chimneys ( I mean can lights) and one of the kitchen walls containing said soffit was common to the main bath where there was a fairly good size whole cut in the wall and vanity back for plumbing (the reason why this interior bath with no window and no heating register was leakier than all the other rooms)  When I can, I'll post a picture of the "panned return" for the master bedroom -- the one where you can see the backside of the fiberglass tub -- NMEB!

NMEB is why electric air handlers get installed instead of heat pumps...

RSS

Discussion Forum

Got insulation?

Started by Debra Little. Last reply by Jason Raddenbach May 25. 2 Replies

Return Possum

Started by Stefan Peter-Contesse. Last reply by Alice La Pierre Oct 26, 2015. 1 Reply

Easy Water Heater Venting

Started by Kari Sauder. Last reply by Matthew Lutz Oct 23, 2014. 22 Replies

Thank-less water heater

Started by Andy Simms. Last reply by Dennis Heidner Jun 13, 2013. 12 Replies

Latest Activity

Blake Shurtz posted a discussion

Replacement for Energy Conservatory Flow-blaster

It's too bad that the flow-blaster is no longer being produced or technically supported. Does…See More
1 hour ago
Diane Chojnowski replied to Mike Rogers's discussion Home Energy Pros and #MeToo
"Mike, thanks so much for supporting women and the #MeToo campaign. Women everywhere  have…"
3 hours ago
Profile IconBrian Cizmar, Charles Allen, Charles Buell and 1 more joined Home Energy Pros Forum
3 hours ago
Mike Rogers posted a discussion

Home Energy Pros and #MeToo

If it doesn't seem obvious why a discussion of …See More
7 hours ago
David Butler replied to David Butler's discussion How would you insulate this roof?
"Sean Lintow proposed rails and clips (re: first comment in this discussion), but in the context of…"
22 hours ago
Brad Cook replied to David Butler's discussion How would you insulate this roof?
"I missed where the suggestion for rails came in. The plywood would not need any rails. 4+ inches is…"
yesterday
David Butler replied to David Butler's discussion How would you insulate this roof?
"I'm a little confused about the necessity and purpose of using support rails if working on…"
yesterday
David Butler replied to David Butler's discussion How would you insulate this roof?
"If you insulate master bedroom and family room from below, you definitely need more R-value than…"
yesterday

Photos

  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service