In Part I of this series on designing for high performance, we discussed the control of moisture flow at foundations. We showed you this detail (below) from the Proud Green Home at Serenbe and reviewed the practices that we and the builder are employing for keeping unwanted moisture out of the building.

Looking back, we said the biggest opportunity in designing for high performance is in controlling the flow of heat, air and moisture. Today, we will focus on controlling heat. In other words, we want to keep heat in it’s place. Out in the summer, and inside in the winter. We’ve designed fairly simple strategies that will go a long way in keeping the homeowners in this house comfortable. Controlling air flow will be discussed in Part III.

From High to Low, and From Hot to Cold

A little physics primer before we get too far. Hot air is simply air molecules that are under high pressure, and cold air molecules are under low pressure. Not unlike people, the molecules migrate from high pressure situations (say, at work) to low pressure situations (say, the bar). With me so far?

Let’s apply it to a real world situation in a home. Have you ever heard the phrase, “hot air rises”? It simply means that the high pressure (hot) air is going (rising) to where there is low pressure (cold) air. In the case of a home in winter, the hot air inside is migrating to the cold (low pressure) attic, and/or the ambient conditions on the other side of the roof. So, what seams like a phenomenon of rising heat is really almost drawing process, where the cold air draws the hot. High to low. Hot to cold. Got it?

Control That Heat!

At the foundation, this phenomenon occurs sideways, downward, upward, or all three ways. When you’re dealing with a slab-on-grade in the Southeast United States (Climate Zone 3), like the one in the Sernebe Residence (near Palmetto, GA), heat will travel SIDEWAYS. And, because we spend more money on heating than cooling in this part of Georgia (yes, it’s true), that’s a big concern.

Stopping this heat flow is one of the most often missed opportunities in these types of climate zones (mixed-humid), and it leads to unnecessarily high heating bills. Even the smallest amount of thermal “protection” can go a long way.

Designing for High Performance Foundation Detail Controlling Heat Flow

For the Proud Green Home, we’re stopping the sideways heat flow by putting a continuous layer of Cellofoam PermaBG Expanded Polystyrene (EPS) foam board. Because the movement of heat increases as the temperature difference increases, we loose more heat in winter than we gain in the summer. The delta T (temperature difference) in winter is as much as 60-70 degrees Fahrenheit, and in the Summer, the highest delta T may be 30-40. This is why homes in the Northeast and Canada are “super-insulated”. They have delta Ts in the 80s, 90s, and higher, and loose way more heat.

We’ll talk more about this in Part 3, but what I’ve just explained is the reason that it makes more sense to invest more in air sealing a home than insulating it in the climate zones 1-3 (warm to hot), maybe even 4. To be clear, though, air sealing is just as important in cold climates as it is warm and hot climates. In fact, the only thing more important in high performance, healthy homes, is keeping the water out (Part I).

Beyond The Slab

In the above grade walls, we are filling the 2×8 framed cavities with blown-in fiberglass insulation (B.I.B.S.), with an R-Value of of just over 4 per inch (total R-30), and using the integrated layer of polyisocyanurate foam (r-value = 3.6) in the Zip System® R-Panel wall sheathing for a continuous thermal barrier.

In a future post, perhaps, we will discuss how and why continuous insulation (like that in the R-Panel) should be used to provide a thermal break between ambient conditions and wood framing in an exterior wall, floor or roof assembly. The condition is called thermal bridging when you have a material that is in contact with ambient conditions on one side, and conditioned space on the other, and heat moves through that material like a car does on a bridge. In our case, we are stopping that bridge with the continuous insulation. The heat (during winter months) on the inside essentially hits a wall when it reaches the foam, and stays inside where it belongs.

- Written by Chris Laumer-Giddens, Architect, HVAC Designer, Building Science Professional, Certified HERS Rater.

Tags: controlling, design, efficient, energy, flow, heat, high, performance, slab-on-grade

Views: 773

Discussion Forum

Whats the Consensus of this group Define "Energy Efficiency"

Started by Barry NewDelman. Last reply by John Nicholas Jan 16, 2014. 1 Reply

No More "Damn Architects!" - The Case for Integrated Design

Started by Chris Laumer-Giddens. Last reply by Dennis Heidner Jan 16, 2014. 6 Replies

Energy Efficient Design for the not so rich

Started by James McGarvey. Last reply by Greg La Vardera Apr 11, 2013. 7 Replies

Latest Activity

Blake Shurtz posted a discussion

Replacement for Energy Conservatory Flow-blaster

It's too bad that the flow-blaster is no longer being produced or technically supported. Does…See More
23 minutes ago
Diane Chojnowski replied to Mike Rogers's discussion Home Energy Pros and #MeToo
"Mike, thanks so much for supporting women and the #MeToo campaign. Women everywhere  have…"
2 hours ago
Profile IconBrian Cizmar, Charles Allen, Charles Buell and 1 more joined Home Energy Pros Forum
3 hours ago
Mike Rogers posted a discussion

Home Energy Pros and #MeToo

If it doesn't seem obvious why a discussion of …See More
6 hours ago
David Butler replied to David Butler's discussion How would you insulate this roof?
"Sean Lintow proposed rails and clips (re: first comment in this discussion), but in the context of…"
21 hours ago
Brad Cook replied to David Butler's discussion How would you insulate this roof?
"I missed where the suggestion for rails came in. The plywood would not need any rails. 4+ inches is…"
yesterday
David Butler replied to David Butler's discussion How would you insulate this roof?
"I'm a little confused about the necessity and purpose of using support rails if working on…"
yesterday
David Butler replied to David Butler's discussion How would you insulate this roof?
"If you insulate master bedroom and family room from below, you definitely need more R-value than…"
yesterday

Photos

  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service