We know, we know. There’s a lot right with this picture, such as the gorgeous view of Lake Tahoe in the background and the awesome powder for skiing. But from a whole-house-as-a-system perspective, what’s wrong with this picture? What is the owner trying to do, and what would be a better solution?

Thanks to our own Larry Zarker, BPI CEO, for sending in this dandy shot. He offers the following Winston Churchill quote to explain what’s going on here: “You can always trust the Americans to get it right, after they have exhausted every other possibility”.

 

Think you know what the problem is, as well as the solution? Send it to us at lmcdowell@bpi.org.

Tags: April, Building, Chump, Newsletter, Performance, Stump

Views: 193

Replies to This Discussion

Congratulations to Craig Bird of Preston Insulation in Tucson, Arizona for winning last month’s “What’s wrong with this picture?”contest. Craig was not only the first person to send in the correct answer. His answer was far and away the most comprehensive, and dare we say, the most elegant in illustrating what in the world of home performance was wrong with the picture, and what should be done about it.

The picture shows a snow-bound house in front of Lake Tahoe, its roof zig zagged with heat strips.  Says Craig:

“The problem is ice dams.  The home most likely had melting of roof snow which then refroze and created ice dams possibly causing water damage or excessive ice buildup at roof edges. This caused the homeowner to install energy intensive heat strips to melt the ice dams and jack their electric bill through the roof during snow events.  

 

This is caused by:

1)     Air leakage from penetrations near exterior wall

2)     Heat sources close to exterior wall such as heating ducts or recessed lighting cans

3)     Insulation in contact with roof sheathing causing thermal bridging to roof deck

4)     Lack of soffit ventilation

 

The solution:

1)     Air seal exterior top plate with spray foam. It is also important to air seal any other penetration which is delivering heat to the underside of the roof deck.

2)     If recessed lighting is installed near exterior walls, the cans should be ICAT rated to prevent air flow through the fixture. An inexpensive air tight trim kit may also be purchased to avoid changing out fixture itself. Heating duct boots can be sprayed with 2 part foam to prevent heating of roof deck.

3)     Install soffit ventilation at code recommended level at EVERY BAY that is affected.

4)     Install insulation baffles at all soffit edges in order to provide a path for ventilation and carry away any remaining heat transferred from house and cool roof deck. This also prevents insulation from contacting the roof deck (causing thermal bridging).

 

Since it is often difficult to get full insulation amounts at the soffit edge due to clearance, an optimal solution would involve installing ventilation baffles and using spray foam insulation against the baffle and as far in until a full amount of blown insulation may be used. This solution also seals any air exfiltration through the wall top plate at the same time. 

RSS

Latest Activity

Profile IconSean Wiens and David Butler joined Chris Laumer-Giddens's group
Thumbnail

Energy Efficient Design

Energy efficiency starts at the drafting table...How architects and designers can help buildings…See More
4 hours ago
Profile IconSean Wiens and David Butler joined Mark Richardson's group
Thumbnail

Renewable Energy

This group will focus on the issues associated with incorporating renewable energy sources like…See More
4 hours ago
Al Tibbs posted photos
5 hours ago
Al Tibbs replied to Bob Krell's discussion What Do You Do When You Find Suspected Mold? in the group Healthy Indoors (IAQ)
"In any case where there is visible mold present, I would begin with a thorough VISUAL assessment of…"
6 hours ago
Al Tibbs joined Bob Krell's group
Thumbnail

Healthy Indoors (IAQ)

The Healthy Indoors group is focused on indoor air quality (IAQ), mold, moisture control, radon,…See More
6 hours ago
David Byrnes posted a blog post

Strategies for Hiring and Interviewing for Home Performance Professionals

Hire slow and fire fast.  It’s a phrase that experienced managers and human resources professionals…See More
6 hours ago
David Butler posted discussions
7 hours ago
David Butler replied to Don Fugler's discussion joining ducts in the group HVAC
"Static pressure drop through a straight length of pipe is a function of friction rate, and friction…"
11 hours ago

Photos

  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service