We know, we know. There’s a lot right with this picture, such as the gorgeous view of Lake Tahoe in the background and the awesome powder for skiing. But from a whole-house-as-a-system perspective, what’s wrong with this picture? What is the owner trying to do, and what would be a better solution?

Thanks to our own Larry Zarker, BPI CEO, for sending in this dandy shot. He offers the following Winston Churchill quote to explain what’s going on here: “You can always trust the Americans to get it right, after they have exhausted every other possibility”.

 

Think you know what the problem is, as well as the solution? Send it to us at lmcdowell@bpi.org.

Tags: April, Building, Chump, Newsletter, Performance, Stump

Views: 192

Replies to This Discussion

Congratulations to Craig Bird of Preston Insulation in Tucson, Arizona for winning last month’s “What’s wrong with this picture?”contest. Craig was not only the first person to send in the correct answer. His answer was far and away the most comprehensive, and dare we say, the most elegant in illustrating what in the world of home performance was wrong with the picture, and what should be done about it.

The picture shows a snow-bound house in front of Lake Tahoe, its roof zig zagged with heat strips.  Says Craig:

“The problem is ice dams.  The home most likely had melting of roof snow which then refroze and created ice dams possibly causing water damage or excessive ice buildup at roof edges. This caused the homeowner to install energy intensive heat strips to melt the ice dams and jack their electric bill through the roof during snow events.  

 

This is caused by:

1)     Air leakage from penetrations near exterior wall

2)     Heat sources close to exterior wall such as heating ducts or recessed lighting cans

3)     Insulation in contact with roof sheathing causing thermal bridging to roof deck

4)     Lack of soffit ventilation

 

The solution:

1)     Air seal exterior top plate with spray foam. It is also important to air seal any other penetration which is delivering heat to the underside of the roof deck.

2)     If recessed lighting is installed near exterior walls, the cans should be ICAT rated to prevent air flow through the fixture. An inexpensive air tight trim kit may also be purchased to avoid changing out fixture itself. Heating duct boots can be sprayed with 2 part foam to prevent heating of roof deck.

3)     Install soffit ventilation at code recommended level at EVERY BAY that is affected.

4)     Install insulation baffles at all soffit edges in order to provide a path for ventilation and carry away any remaining heat transferred from house and cool roof deck. This also prevents insulation from contacting the roof deck (causing thermal bridging).

 

Since it is often difficult to get full insulation amounts at the soffit edge due to clearance, an optimal solution would involve installing ventilation baffles and using spray foam insulation against the baffle and as far in until a full amount of blown insulation may be used. This solution also seals any air exfiltration through the wall top plate at the same time. 

RSS

Discussion Forum

BPI is Hiring!

Started by Quinn Korzeniecki. Last reply by Diane Chojnowski Jun 29. 1 Reply

Latest Activity

B Eric Bell liked Bob Krell's group Healthy Indoors (IAQ)
8 hours ago
John Krochmalny posted a discussion

Psychrometric Chart Training

Looking through the various areas of this site, I didn't see too much information or training on…See More
10 hours ago
Profile IconMike Malek, Avery T. Phillips and Sarah Burger joined Home Energy Pros Forum
12 hours ago
Dannie Jackson's blog post was featured

Core Heat And Other Concepts

  In some places the use of solar heated liquids from hot water solar panels are used to provide…See More
16 hours ago
Michael Duclos replied to Brad Cook's discussion Too many Heat Pump Water Heaters in a basement?
"I’ve been looking into Sanden for a multi-family PH near Laconia, NH, ASHRAE 99.6% temp is…"
16 hours ago
Profile IconTroy Spindler, Mike Berg, Andrew McDowell and 4 more joined Home Energy Pros Forum
yesterday
David Butler replied to Brad Cook's discussion Too many Heat Pump Water Heaters in a basement?
"theoretically, let's say you perfectly isolate the HPWH from a heat source. The HPWH's…"
Monday
David Butler replied to David Butler's discussion How would you insulate this roof?
"Interesting idea. Commercial roof on a slope! Typical density for roofing spray foam is 2.5 to 3.0…"
Monday

Photos

Loading…
  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service