Before we had our high tech tools, how did we know if there was insulation in the walls? What were the methods?

How funny that I can use a camera but than can't figure out how was it done in the past without drilling holes on the wall and than you had to patch it? That doesn't seem like a cost effective way to bid a job. Or is it another rule of thumb? Like In So. Cal houses built before the 70's we can assume that there is no wall insulation. I am sure on the East Coast that insulation is a MUST. 

Views: 97

Replies to This Discussion

Well I just simply pop the cover off a few light switches & electrical outlets & shined a light in there. If I didn't see anything I would take a bent coat hanger & use it to fish around in there some.

 

Generally if we are remodeling a house / gutting  a room to the studs I will add in new insulation anyways due to new electrical, plumbing, etc... & the old insulation is probably shot. The only surprise I had was the 1879 remodel we did where it was fully packed with a wool type insulation that stayed in place & was still in great shape.

A crocheting hook used at an electrical outlet on an exterior wall can reveal the presence or lack of insulation.

Common practice in the Minneapolis area for the past 20 years has been to drill a 2” hole in a closet on an outside wall and snap a plastic plug into the hole after verifying the insulation level.  This would be done for any home built before about 1970.  It is possible for a wall to look insulated using the IR and have only 1.5 inches of insulation in the wall.  In our climate it is cost effective to dense pack cellulose into a wall that has an existing 1.5” insulation batt.  Sometimes on homes build before 1920, the walls will have no insulation but have back-plaster.  Back-plaster is an additional layer of plaster that was installed in the center of the wall cavity, making it more much expensive to insulate.  The IR is a great tool but it has limitations.

In reply to probing around ext. wall outlets, the problem is that batt insulation is usually installed poorly. By only probing in these locations you run the risk of determining that no existing insul. is in the wall because it was cut out too big around the box. The other error is compacted insul. around the box because it was not cut at all.

I would agree that the best practice is to drill inspection holes in the closet of an exterior wall and plug them. Of course this is dependent on H/O approval.

RSS

Discussion Forum

Water Saver or Gimmick?

Started by Sean Lintow Sr. Last reply by David Butler on Friday. 22 Replies

Moisture/Mold on rim joist

Started by John Shillito. Last reply by Bob Krell on Thursday. 11 Replies

Radon - Passive Systems

Started by Sean Lintow Sr. Last reply by Bryan Gabriel Jan 5. 5 Replies

Vented Soffit! DO or DON'T?

Started by Daniel Baur-McGuire. Last reply by Daniel Baur-McGuire Nov 15, 2016. 13 Replies

Duct Testing - is a change in order?

Started by Sean Lintow Sr. Last reply by Sean Lintow Sr Aug 6, 2015. 20 Replies

Latest Activity

John Krochmalny posted a discussion

Psychrometric Chart Training

Looking through the various areas of this site, I didn't see too much information or training on…See More
2 hours ago
Profile IconMike Malek, Avery T. Phillips and Sarah Burger joined Home Energy Pros Forum
3 hours ago
Dannie Jackson's blog post was featured

Core Heat And Other Concepts

  In some places the use of solar heated liquids from hot water solar panels are used to provide…See More
7 hours ago
Michael Duclos replied to Brad Cook's discussion Too many Heat Pump Water Heaters in a basement?
"I’ve been looking into Sanden for a multi-family PH near Laconia, NH, ASHRAE 99.6% temp is…"
8 hours ago
Profile IconTroy Spindler, Mike Berg, Andrew McDowell and 4 more joined Home Energy Pros Forum
yesterday
David Butler replied to Brad Cook's discussion Too many Heat Pump Water Heaters in a basement?
"theoretically, let's say you perfectly isolate the HPWH from a heat source. The HPWH's…"
Monday
David Butler replied to David Butler's discussion How would you insulate this roof?
"Interesting idea. Commercial roof on a slope! Typical density for roofing spray foam is 2.5 to 3.0…"
Monday
Summer Redman added a discussion to the group Job Board
Thumbnail

Hiring 2 Training Specialists in Champaign-Urbana, Illinois

The Applied Research Institute (ARI) at the University of Illinois at Urbana-Champaign is seeking…See More
Monday

Photos

Loading…
  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service