Before we had our high tech tools, how did we know if there was insulation in the walls? What were the methods?

How funny that I can use a camera but than can't figure out how was it done in the past without drilling holes on the wall and than you had to patch it? That doesn't seem like a cost effective way to bid a job. Or is it another rule of thumb? Like In So. Cal houses built before the 70's we can assume that there is no wall insulation. I am sure on the East Coast that insulation is a MUST. 

Views: 103

Replies to This Discussion

Well I just simply pop the cover off a few light switches & electrical outlets & shined a light in there. If I didn't see anything I would take a bent coat hanger & use it to fish around in there some.

 

Generally if we are remodeling a house / gutting  a room to the studs I will add in new insulation anyways due to new electrical, plumbing, etc... & the old insulation is probably shot. The only surprise I had was the 1879 remodel we did where it was fully packed with a wool type insulation that stayed in place & was still in great shape.

A crocheting hook used at an electrical outlet on an exterior wall can reveal the presence or lack of insulation.

Common practice in the Minneapolis area for the past 20 years has been to drill a 2” hole in a closet on an outside wall and snap a plastic plug into the hole after verifying the insulation level.  This would be done for any home built before about 1970.  It is possible for a wall to look insulated using the IR and have only 1.5 inches of insulation in the wall.  In our climate it is cost effective to dense pack cellulose into a wall that has an existing 1.5” insulation batt.  Sometimes on homes build before 1920, the walls will have no insulation but have back-plaster.  Back-plaster is an additional layer of plaster that was installed in the center of the wall cavity, making it more much expensive to insulate.  The IR is a great tool but it has limitations.

In reply to probing around ext. wall outlets, the problem is that batt insulation is usually installed poorly. By only probing in these locations you run the risk of determining that no existing insul. is in the wall because it was cut out too big around the box. The other error is compacted insul. around the box because it was not cut at all.

I would agree that the best practice is to drill inspection holes in the closet of an exterior wall and plug them. Of course this is dependent on H/O approval.

RSS

Discussion Forum

Water Saver or Gimmick?

Started by Sean Lintow Sr. Last reply by Keith Tripp Oct 20. 23 Replies

Moisture/Mold on rim joist

Started by John Shillito. Last reply by Bob Krell Oct 12. 11 Replies

Radon - Passive Systems

Started by Sean Lintow Sr. Last reply by Bryan Gabriel Jan 5. 5 Replies

Vented Soffit! DO or DON'T?

Started by Daniel Baur-McGuire. Last reply by Daniel Baur-McGuire Nov 15, 2016. 13 Replies

Duct Testing - is a change in order?

Started by Sean Lintow Sr. Last reply by Sean Lintow Sr Aug 6, 2015. 20 Replies

Latest Activity

Summer Reyes's blog post was featured

Equipment We Use: Detecting Water With Infrared Cameras

You know water is somewhere on the property, you can smell the mildew, but can't determine the…See More
52 minutes ago
Profile IconGlenn Hourahan and Joseph Frasier joined Home Energy Pros Forum
56 minutes ago
Alfredo Baccari added a discussion to the group Job Board
Thumbnail

HERS or/and BPI Energy Inspector in SF Bay Area (SAN JOSE, CA).

ELEM3NTS is a leading energy efficient consulting company specializing in residential homes. We…See More
1 hour ago
Alfredo Baccari joined Diane Chojnowski's group
Thumbnail

Job Board

This group is for posting jobs related to all aspects of the home performance industry including…See More
2 hours ago
David Byrnes's blog post was featured

Strategies for Hiring and Interviewing for Home Performance Professionals

Hire slow and fire fast.  It’s a phrase that experienced managers and human resources professionals…See More
5 hours ago
Dara Bowser replied to Don Fugler's discussion joining ducts in the group HVAC
"Good to hear you have clean dryer ducts Don. The dryer duct issues that we run into are…"
21 hours ago
Don Fugler replied to Don Fugler's discussion joining ducts in the group HVAC
"David, If the IMC mandates metal dryer duct and prohibits metal screws, they must be accepting…"
22 hours ago
David Butler replied to Don Fugler's discussion joining ducts in the group HVAC
"I never checked that before. Checking now... Section M1502.4.2 of the International Residential…"
22 hours ago

Photos

  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service