Wood burning fireplace on 13 year old home in Wisconsin. Exterior wall with cantilevered chase. During blower door test I found noticeable air leakage to the inside from above the metal firebox. Would naturally suspect air leakage from the top and back of the chase. However, there are 2 air intakes on the chase - one is for outside air to the firebox as expected. The other one seems to be just an open vent to the chase. Outside air was freely entering the 2nd vent and into the home while building was depressurized.

Anyone know what this vent is for, and does it need to be there?

I don't have a picture, but the two exterior vents were side by side. Sorry too that I don't know the make of the fireplace. They have no complaints with the fireplace area, but I'd like to know.

 

Thanks,

John

Views: 2476

Replies to This Discussion

I imagine is pretty hard to tell much without the brand and its installation instructions to know what was required for that particulare fireplace model; not all fireplaces are built nor installed the same. It'll be interested to know how well sealed and insulated were the cantilever and chase before installing the firebox.

Does this home has a second direct vent fireplace between the 2 side windows? 

That is correct Armando.

I'm sure we won't be doing anything intrusive with regard to the chase, but I'd like to know if we could seal off the vent, as that was certainly a pathway for outside air to enter into the home.

Yes. Its correct.

John:  The chase is unlikely to have been treated as "conditioned" space by the builder.  If it is not air sealed it performs basically like a small garage with a fireplace instead of a car in it. 

Current code requires an air barrier in the fireplace chase, but I have never succeeded in retrofitting a chase like the one shown in your picture.

RSS

Discussion Forum

Water Saver or Gimmick?

Started by Sean Lintow Sr. Last reply by Keith Tripp Oct 20. 23 Replies

Moisture/Mold on rim joist

Started by John Shillito. Last reply by Bob Krell Oct 12. 11 Replies

Radon - Passive Systems

Started by Sean Lintow Sr. Last reply by Bryan Gabriel Jan 5. 5 Replies

Vented Soffit! DO or DON'T?

Started by Daniel Baur-McGuire. Last reply by Daniel Baur-McGuire Nov 15, 2016. 13 Replies

Duct Testing - is a change in order?

Started by Sean Lintow Sr. Last reply by Sean Lintow Sr Aug 6, 2015. 20 Replies

Latest Activity

Dara Bowser replied to Don Fugler's discussion joining ducts in the group HVAC
"Good to hear you have clean dryer ducts Don. The dryer duct issues that we run into are…"
13 hours ago
Don Fugler replied to Don Fugler's discussion joining ducts in the group HVAC
"David, If the IMC mandates metal dryer duct and prohibits metal screws, they must be accepting…"
15 hours ago
David Butler replied to Don Fugler's discussion joining ducts in the group HVAC
"I never checked that before. Checking now... Section M1502.4.2 of the International Residential…"
15 hours ago
Joseph Frasier is now a member of Home Energy Pros Forum
15 hours ago
Don Fugler replied to Don Fugler's discussion joining ducts in the group HVAC
"Brendan, Thanks for that response. Because of your warning, I just went down to the basement and…"
19 hours ago
Brendan Reid replied to Don Fugler's discussion joining ducts in the group HVAC
"Hi Don, Summary: DRYER VENT: screws bad idea, possibly prohibited by code. METAL DUCT: must be…"
19 hours ago
Profile IconBrendan Reid and David Butler joined Allison A. Bailes III's group
Thumbnail

HVAC

HVAC design, Manuals J, S, T, & D, Duct leakage, Air flow, ENERGY STAR new home requirements,…See More
19 hours ago
Profile IconSean Wiens and David Butler joined Chris Laumer-Giddens's group
Thumbnail

Energy Efficient Design

Energy efficiency starts at the drafting table...How architects and designers can help buildings…See More
yesterday

Photos

  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service