Where to install the vapor barrier for a finished basement?

I have an audit customer that is in the process of finishing his basement. The basement foundation walls are poured concrete. He has installed a polyethylene vapor barrier over the concrete wall per his brother's instructions who is a builder. He plans to install unfaced insulation in the 2 by 4 stud walls that are 2 inches away from the concrete wall. He will be also installing drywall and heating the space with his existing HVAC unit. This is an all-electric two story home located in Ohio.

 

I'm already recommending he seal the entire rim joist with foam since they are leaking a lot of air. The rim joists are currently fitted with faced fiberglass batts. My thoughts are to advise him to also foam the entire basement wall but I'm not sure this is the correct or the best solution. If he decides to install fiberglass batt insulation in the 2 by 4 walls, where should the vapor barrier be installed? The poured cement basement walls are dry with good drainage outside so I'm thinking the vapor barrier should be installed between the drywall and insulation since the basement will be a conditioned space.

Views: 60597

Reply to This

Replies to This Discussion

I'm referencing Joe Lstiburk's "Cold Climates" You should not install poly on the walls in the assembly. It will cause the wall to retain moisture. The key is to let the walls dry to the inside or the outside. I would also not use fiberglass in the basement because it is hydrophilic. A water resistant insulation would be a better material to use. I recommend you get a copy of "Cold Climates" it covers all the different areas in a house and the best methods for building and insulating.
Thanks Chris for your feedback. I will get Joe Lstiburk's book so I can add it to my reference library. 
You're very welcome.

Also, review the work of the Pat Huelman and the folks of the Cold Climate Housing Center. Pat and his people have done a lot of work in this area. And he and Dick Stone do a lot of training -- Affordable Comfort, the Duluth EDC conference, etc.

 

I don't believe any of their work contradicts the info in the "Builder's Guide: Cold Climates" book. But they may well have info on the most recent "miracle" materials out there intended to "allow" building assemblies that will just never work. (Like this goofy idea that you can successfully put a functioning vapor barrier on the warm side of a below-grade concrete wall!) 

Thanks Don for making me aware of Pat Huelman group. I'll definetly review their findings.

Jim,

Your question and the subsequent responses got me thinking. 

I tell myself I should know the answer to this question but I found myself wavering a bit.

I have “Cold Climates” but it has been awhile since I have reviewed it and looked at this wall profile.

 

Out of curiosity I searched the web and here is what I found at an EPA site.

http://www.epa.gov/indoorairplus/technical/moisture/1_12.html

 

“An appropriate assembly for the inside of a basement wall consists of 1 in. of plastic foam board or closed-cell polyurethane spray foam followed by a stud wall with fiberglass insulation filling the cavities. This assembly is covered with moisture- and mold-resistant gypsum board covered by two coats of latex paint. The foam board serves two purposes: providing a capillary break between the foundation wall and the stud wall and keeping warm, humid basement air away from the earth-chilled foundation. It is good practice to put 1 in. of foam board beneath the sole plate of the stud wall and the basement floor and to leave a ½-in. gap between the basement floor and the bottom of the gypsum board. Doing so provides protection from minor floods and damp concrete floors.”

 

Clicking the link provides additional explanation and context for this strategy.

I wonder if this is consistent with the other resources mentioned. If not i would like to hear others thoughts.

You can find an excellent publication on this question at http://www.buildingscience.com/documents/reports/rr-1003-building-a....  The publication presents many solutions and rates them on several criteria.  They also conducted detailed thermal and moisture modeling.

I put 2" XPS on my basement walls as a temporary way to add some insulation before I got to the task of finishing the basement walls. I did not seal the joints between the sheets or the gaps at the top and bottom of the sheets.  I had lots of ice on the top of the foundation wall and ice at every joint and gap down to the soil line.  A well sealed vapor barrier at the foundation wall is absolutely critical to preventing moisture problems.

After seeing the moisture/ice problems first hand, I think I will insulate the stud walls with closed cell foam to assure that I have no air leaks.  This will cost more but the peace of mind is worth it.  I live in a very cold climate near Yellowstone National Park.  We have had many consecutive days of -20 to -30 F this winter.  I am sure this contributed the ice formation behind the XPS and on top of the foundation wall.

polyethylene vapor barrier is the most common that the contractors use. See this http://www.agmrenovations.com/safebasement/ incase you need any information

No first-hand experience, but that stuff looks like spray-on bulk water proofing material not moisture seal. And why are they spraying it on after the stud wall was erected and not before?

Since he's also in Ohio and has a great deal of experience, you might want to reach out to Nate Adams at Energy Smart Home Performance for his opinion.

RSS

Forum Discussions

Insulation Blower Recommendations?

Started by Jim Conlon in General Forum. Last reply by Brad Cook 8 hours ago. 5 Replies

Best brands for furnace

Started by Jignesh in General Forum. Last reply by Eric Kjelshus 11 hours ago. 2 Replies

Efficiency of furnace

Started by Jignesh in General Forum. Last reply by Eric Kjelshus 12 hours ago. 10 Replies

2005 EPAct tax credit

Started by Mandy Leazenby in General Forum. Last reply by Sean Lintow Sr Feb 15. 3 Replies

Latest Activity

Brad Cook replied to Jim Conlon's discussion Insulation Blower Recommendations?
"Most rental machines will not put out the minimum required pressure for dense-packing. There are…"
8 hours ago
Brad Cook replied to Jim Conlon's discussion Insulation Blower Recommendations?
"We have been using the Intec Force II for almost 10 years. It only takes about 1 1/2 bags at a…"
8 hours ago
Eric Kjelshus replied to Jim Conlon's discussion Insulation Blower Recommendations?
"Most generator are more efficiency at 240 volt.   Its  about the total watts more…"
11 hours ago
Eric Kjelshus replied to Jignesh's discussion Best brands for furnace
"Its more about the install and air flow than the box brand,  Most brands about the same if you…"
11 hours ago
Eric Kjelshus replied to Jignesh's discussion Efficiency of furnace
"OK lets say you have a gravity air system with a 80% burn on heat exchanger with out the 8"…"
12 hours ago
John Nicholas replied to Jignesh's discussion Efficiency of furnace
"System Efficiency is great.  Not much use, if you don't intend to fix the various…"
20 hours ago
John Nicholas replied to Jignesh's discussion Efficiency of furnace
"Furnaces and all HVAC Equipment is rated by AHRI.  You can get the certification as to the…"
21 hours ago
Jacob Corvidae replied to Diane Chojnowski's discussion Support Mike Rogers in the group News & Announcements
"Hey Mike! We're all routing for you! Don't hesitate to ask for help.  Jacob"
21 hours ago
Jacob Corvidae joined Diane Chojnowski's group
Thumbnail

News & Announcements

Share your news and announcements with the community in this group.To post news or an announcement,…See More
21 hours ago
Diane Chojnowski added a discussion to the group News & Announcements
21 hours ago
Profile IconJeannette Moore, David Carson, Jesse Smith and 3 more joined Home Energy Pros Forum
22 hours ago
Home Energy Magazine's blog post was featured

How We Turned Our House into a Giant Foam Box, Part I — Wall Insulation By Wen Lee

Chris Stratton and Wen Lee are a husband-and-wife team living in the Los Angeles area who are DIY…See More
yesterday
Home Energy Magazine posted a blog post

How We Turned Our House into a Giant Foam Box, Part I — Wall Insulation By Wen Lee

Chris Stratton and Wen Lee are a husband-and-wife team living in the Los Angeles area who are DIY…See More
yesterday
Chris Stratton replied to Chris Stratton's discussion Technical question about mini split heat pump line set maximum length
"Hi Chris, Thanks again for your help. Update: the system is now up and running. Chris"
yesterday
Home Performance Coalition's blog post was featured

From Philly to DC: Join Us on Capitol Hill

By now you have probably heard – as part of this year’s …See More
yesterday
Diane Chojnowski added a discussion to the group News & Announcements
Thumbnail

Nominate a visionary leader for the Linda Wigington Leadership Award

The Linda Wigington Leadership Award celebrates visionary leaders doing extraordinary work to…See More
yesterday
Home Performance Coalition liked Chris Morin's blog post HVAC: A Fast Growing Career Opportunity
Wednesday
Home Performance Coalition liked Diane Chojnowski's blog post Home Performance Coalition Calls on Congress to Support Federal Energy Efficiency Programs
Wednesday
Home Performance Coalition liked Home Energy Magazine's blog post Andrew Scatizzi- Stick to the Basics in New Construction
Wednesday
Home Performance Coalition posted blog posts
Wednesday

Photos

  • Add Photos
  • View All

© 2018   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service