A client had a new double wide set (27x56) in1997 a couple years later had an addition (27x20) to the west side with 27x20 attached garage to that addition, the general contractor tells the client a bigger furnace will be needed. He (general contractor) brings in his HVAC guy who installs a furnace clearly stamped "Installation for site built only", the front of the return box was hacked out to provide for a 16x20 filter plus the back has a run coming off of it into the master bed closet with a filter slot (no filter in place)down into the crawl and up into the wall cavities of the addition all metal return ducting uninsulated in crawl. The supply to addition comes off the original duct board below the furnace through the crawl to four insulated flex runs in addition and for some reason they insulated ,or tried to,  the metal ducting in addition crawl but not under manufacture home crawl and to make sure the owner got a good job the jumper duct was cut about four out from the furnace and left that way. The only thing I can come up with is they were going to tie into to the new heat run and forgot. So forget the general contractor, HVAC guy and last but not least the county inspector, so now what. As far as I'm concered that furnace has got to go and "Manufacture Home" approved installed, period. For the supply runs remove all that ducting, seal duct board back up and tie into bottom of original ducting at each west end run with insulated flex to existing boots, and naturally new jumper. I'm thinking the return in addition can go, the passage way to addition is over 8'. What are your thoughts, am I on the right track or in line with the three fore mentioned proffesionals. "The things that make your head go," BOOM ! " 

Views: 158

Reply to This

Replies to This Discussion

The manufacture home has higher SP ( rated Static Pressure) supply and no return  so some are rated to .8 to 1" in water vs most res are .5 in water.  Most Manufacture homes have a little room off the hall way  so the fan is a foot from door with wimpy filter.  Manufacture home have no branch duct just a 5" stream off the main trunk.     That's 2597 SF and Mob home air handler have higher efficiency  with smaller area,  With the transfer main trunk the efficiency just drops 10-15%

  Manufacture homes furnaces also take outside air on outside the flue pipe and have to buy the chimney from them.  When test system Efficiency (BTU in Vs BTU out) I get mid 40% on new and low 30% on old duct work.    To me it’s just temporally housing with high power bills.

RSS

Forum Discussions

How would you insulate this roof?

Started by David Butler in General Forum. Last reply by Stuart Langley 10 minutes ago. 12 Replies

Psychrometric Chart Training

Started by John Krochmalny in Training. Last reply by Mahendra Shah 1 hour ago. 1 Reply

Dirty solar panels

Started by Evan Mills in General Forum. Last reply by Stacie Bagnasco on Monday. 1 Reply

Latest Activity

Stuart Langley replied to David Butler's discussion How would you insulate this roof?
"So this building has a few issues with air leaks and air leaks have so much to do with discomfort…"
10 minutes ago
Stuart Langley replied to David Butler's discussion How would you insulate this roof?
"John Hatfield has the right idea here for a new roof deck. Polyiso boards always need a good stout…"
17 minutes ago
Keith Tripp replied to Sean Lintow Sr's discussion Water Saver or Gimmick? in the group Best Practices (Residential)
"Interesting to see that recirc. has been in use for many years in some places. It is still a…"
1 hour ago
Mahendra Shah replied to John Krochmalny's discussion Psychrometric Chart Training
"John Thanks for show and tell tutorial"
1 hour ago
Walter Money replied to David Butler's discussion How would you insulate this roof?
"Gentlemen, and ladies, So, as I read this, I see a perfectly good roof that works in serious…"
3 hours ago
tedkidd replied to Bob Blanchette's discussion Tankless Water Heaters... has their time finally come?
"Those are DIY install prices - not that cost is relevant now. If the goal is to go carbon free,…"
3 hours ago
Profile IconAndy Piercefield, Paigh Bumgarner, Blake Reid and 4 more joined Home Energy Pros Forum
4 hours ago
Marc Tannenbaum's blog post was featured

3 Issues HVAC contractors Should Know About Impacting Customer Comfort and Health

There is an epidemic of people suffering in many of the 100 million homes across the U.S.  Many of…See More
5 hours ago

Photos

  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service