As an energy auditor I occasionally see vermiculite in the gas fireplaces. Does anyone know if any of the vermiculite they use(d) for fireplaces has asbestos fibers and if it's safe to run blower door?

Thank you

Tags: Fireplace, Vermiculite

Views: 9843

Attachments:

Reply to This

Replies to This Discussion

I put a drop on the fire place  more for the soot  and light fibers.   You can get 3000 PPM CP  very quick with open flame with rock wool or vermiculite what flame hits.   I have vacked at whole room with a tear drop shape from the soot with open flame.  That fire place pipe is just 1/2 black pipe sc 40 with holes drilled it then the gas runs though the rock wool and other fibers to make it look like "real".   When I took at class on asbestos its listed as vemiculite as a holder.  

when in doubt pressurize. That may not be a bad idea for fireplaces in general. I was suprised the first time I saw vermiculite in a fireplace. By pressurizing you won't pull any air past the fibers from the gaps around the damper making it safe even if yuou have asbestos contaminated vermiculite.

 

Eric, if I understood you opinion correctly you would not do a blower door test if there is any vermiculite in the house no matter what. 

That brings me to an interesting question - what if the fireplace newer than 1978? I see newer houses, built in the 80s and 90s that that have fireplaces with vermiculite in them . 

I would assume that any vermiculite in use since 1978 should have been tested safe. 

Cory, I fully agree, pressurizing is always safer in case you have any sources of contamination. 

It wasn't until about 1994 that it was discovered that there asbestos was found in the vermiculite in the Libby-Owen Mine in Montana, which was the source for 70% of the vermiculite sold in the US. Vermiculite is now considered a hazardous material, unless it has been installed since 1994 and the source can clearly be documented. Lots of information on this topic on the Web.

You are allowed to pressurize the blower door test, assuming that you will not be disturbing asbestos fibers that could enter the house. If vermiculite is in the walls and attic, there may be little opportunity for notable energy savings, and you would not be able to determine where the leaks are with a pressurized test, so why bother?

I have never seen vermiculite in or around a fireplace here in Vermont. Where are you finding this vermiculite in fireplaces?

If you go to a fireplace show floor like midwest fireplace or troost fireplace,  they have 40+ working fireplaces mostly nat gas some wood some press wood with chains/dampers  The very high end home will have a mix of rock wool and vermiculite that nat gas or lp gas will burn into, right on the 1 lb poly bag says vermiculite expanded and its an add on,  replace each year,  mix for look.  I get 300 PPM CO off the flame and 100 +- in flue on low and high gets to 3000 PPM CO flame and 1000 PPM CO flue.    I have seen the vermiculite turn black soot then white soot if burn is good.  If you do not cover the soot/vermiculite/rock wool mix you will get a tear drop shape to the blower door.   Its sold to make the fire places look kinda like wood burning. 

Thank you very much for your reply, it was very helpful. 

I've seen a number of fireplaces with vermiculite both in NY and Oregon.

Does anyone have any data on asbestos in the house from running a blower door?  From the attic, basement or a fireplace?  

I'd check with the local installers as to when the orig. install was and what product they were using.  Grace, etc. stopped producing / selling ACM vermiculite in the mid. 90's.

http://en.wikipedia.org/wiki/Vermiculite

Best,

I am an asbestos inspector. The last two times I have tested fireplace vermiculite it has tested negative so its not automatically asbestos. Since its loose and not affixed to or installed in the building its not a regulated asbestos building material. Therefore, its ok for non-certified building inspectors to grab a sample and have it tested. Just make sure you read up on proper technique and safety precautions. Inspectors can use www.DIYsampletesting.com for national service or you may be able to find a local lab that doesn't mind dealing with single samples and submittals from uncertified persons.

Our weatherization protocol (based on Wisconsin DHS rules) says there is no reliable sampling protocol for asbestos  in vermiculite. The reason (I am told)  is that the asbestos fibers laid in veins in the original ore, and not dispersed through the mine. So it was probably NOT dispersed evenly throughout the roasted/processed vermiculite. We were told you could grab a sample from one joist cavity and it would be completely clean. A second sample, three joist cavities over, from a different bag of product, could be loaded with fibers.

We just treat all vermiculite as an asbestos hazard --  it's considered "friable" asbestos, so we do only pressurized blower door tests. But I don't know that I or anyone I know in Wisconsin, has ever seen these vermiculite-laden gas log systems. I know I'd hesitate to do any blower door test if there were a pile ov vermiculite sitting right there in the living room! 

In my testing experience I am not finding that much variability between samples for attic insulation. Stratification is a bigger issue in terms of variability between locations in that the asbestos is found in the smaller settled fraction at the bottom. When I do sampling I typically don't find areas that only contain coarse material, suggesting that settling within the bags was not that significant. Certainly there is more homogeniety in fireplace vermiculite as it all came from the same bag. There are some valid questions about the reliability of the results however that is true with a number of other types of suspect asbestos materials (e.g. hard plaster and floor tile). I have found that regulators tend to exaggerate concerns because they don't understand the inherent variability associated with testing methods and expect everything to be perfectly legally and statistically defensible when that level of accuracy and precision is not usually needed for small residential projects to be adequately protective.

If its vermiculite treat it as having asbestos, unless you want to pay someone to test it, and I would not do a blower door until it has been proven.

RSS

Forum Discussions

Efficiency of furnace

Started by Jignesh in General Forum. Last reply by Eric Kjelshus 4 hours ago. 6 Replies

Insulation Blower Recommendations?

Started by Jim Conlon in General Forum. Last reply by Cameron Home Insulation 5 hours ago. 2 Replies

2005 EPAct tax credit

Started by Mandy Leazenby in General Forum. Last reply by Sean Lintow Sr on Thursday. 3 Replies

Best brands for furnace

Started by Jignesh in General Forum on Tuesday. 0 Replies

Latest Activity

Eric Kjelshus replied to Jignesh's discussion Efficiency of furnace
"I like looking at system efficiency - Lets say the you have a 95% gas using furnace 100,000…"
4 hours ago
Cameron Home Insulation replied to Jim Conlon's discussion Insulation Blower Recommendations?
"Hi, Rent a Cellulose Insulation Blower from your local Home Depot. Get more information about…"
5 hours ago
Todd Abercrombie liked Barbara Smith's video
yesterday
Jim Hensen replied to Jignesh's discussion Efficiency of furnace
"Great question - what the efficiency rating means is one of the most common questions we we asked.…"
yesterday
Michael Schettine's blog post was featured

Framing production combined with air sealing

Building Tighter Homes with Gasketed FramingIf you follow our blog, you know that we talk quite a…See More
Friday
Profile IconMichael E and Jason Dion joined Home Energy Pros Forum
Friday
Jason Dion joined Sean Lintow Sr's group
Thumbnail

Best Practices (Residential)

Best Building, Retrofitting, or even Auditing Practices - what are they, what should change, what…See More
Friday
Jason Dion joined Michael Stuart's group
Thumbnail

INFRARED THERMOGRAPHY USERS

This group is dedicated to knowledge sharing and discussion of infrared thermography for building…See More
Friday
Jason Dion joined allen p tanner's group
Thumbnail

Energy Auditing Equipment for Sale, Trade or to Purchase

Discuss the pros and cons of the equipment you are interested in prior to purchase. Post equipment…See More
Friday
Jason Dion joined Allison A. Bailes III's group
Thumbnail

HVAC

HVAC design, Manuals J, S, T, & D, Duct leakage, Air flow, ENERGY STAR new home requirements,…See More
Friday
Jason Dion joined Bob Krell's group
Thumbnail

Healthy Indoors (IAQ)

The Healthy Indoors group is focused on indoor air quality (IAQ), mold, moisture control, radon,…See More
Friday
Jason Dion joined Building Performance Institute's group
Thumbnail

Building Performance Institute (BPI)

BPI is the nation's premier standards development, quality assurance and credentialing organization…See More
Friday
Jason Dion joined Diane Chojnowski's group
Thumbnail

Job Board

This group is for posting jobs related to all aspects of the home performance industry including…See More
Friday
Brad Cook replied to Jignesh's discussion Efficiency of furnace
"NO combustion based heating system can ever be 100% efficient, according to the Second Law of…"
Thursday
Brian Robinson commented on Barbara Smith's video
Thumbnail

How to get top performance from your furnace, air conditioner or heat pump

"So glad you highlighted the importance of air sealing & insulating the home form the bottom to…"
Thursday
Brian Robinson replied to Jignesh's discussion Efficiency of furnace
"You also may also want to account for the distribution losses as you move the heat from the…"
Thursday
Michael Schettine posted a blog post

Framing production combined with air sealing

Building Tighter Homes with Gasketed FramingIf you follow our blog, you know that we talk quite a…See More
Thursday
David Butler replied to Jignesh's discussion Efficiency of furnace
"Adding to Sean's comment... The reason a 90%+ furnace uses a PVC flue (as opposed to metal) is…"
Thursday
Barbara Smith's video was featured

How to get top performance from your furnace, air conditioner or heat pump

Video produced as part of our Minnesota heating and cooling system study. Seventhwave
Thursday
DesignTech posted photos
Thursday

Photos

  • Add Photos
  • View All

© 2018   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service