I have a flat roof home with 3 feet of clearance from attic floor to ceiling. It is 1920 square feet, existing home. The space is unvented, and has one access hatch. It is in the master bedroom closet with no close access to a window or door. We plan to spray foam the roof deck. I am struggling to figure out how to ventilate the space during the job without positively pressurizing the attic. The home is stucco, so we do not have an easy way to create a hole to the outside. I typically rent a manhole fan. We can't suck air out of the hatch since overspray would ruin the rented fan (I think, maybe not?) When it is gables, I just leave the gable vents open(or mushrooms) until the very end of the job, and have the fan blow up into the attic hatch and out the gable ends. How do you spray foam guys ventilate an unvented attic space while spraying? We have just started on retrofit market, so most of our jobs have been new homes without these problems.

Views: 321

Reply to This

Replies to This Discussion

Hi Craig,

No direct experience in what you asked, but I have seen the venting process used for asbestos abatement.  In your case, an exhaust fan pulling through a large flex duct down through that hatch and extended as far as necessary.  I have a window fan that roars and I have used it to enhance an IR inspection when the blower door was not part of the consultation.  So even if the fan got contaminated, they aren't that expensive.  A round duct through a square hatch should leave plenty of room for fresh air.  Just thinking out load, good luck.

Bud

Bud - I think that is what we decided, except I will seal the exhaust fan in tight in the hatch, run a 20" flex duct to the outside. Keep a window open and allow the recessed cans to let air into the attic. If that isn't enough air we can always open a supply duct since the attic will be depressurized. Came down to finding the right combo of fan and duct. Can get both for around $100 total. I think the fans will hold up even with some overspray.

There are paper hoods that hook to your compressor hose.  Very slick and inexpensive.  Much better than counting on face masks. 

RSS

Forum Discussions

How would you insulate this roof?

Started by David Butler in General Forum. Last reply by David Butler 13 hours ago. 15 Replies

Psychrometric Chart Training

Started by John Krochmalny in Training. Last reply by Mahendra Shah 16 hours ago. 1 Reply

Dirty solar panels

Started by Evan Mills in General Forum. Last reply by Stacie Bagnasco on Monday. 1 Reply

Latest Activity

tedkidd replied to Bob Blanchette's discussion Tankless Water Heaters... has their time finally come?
"Yeah. Gas water…"
6 hours ago
Eric Kjelshus replied to Bob Blanchette's discussion Tankless Water Heaters... has their time finally come?
"With super cheap natural gas prices now, still worth going all electric?  Tankless needs a lot…"
7 hours ago
Stuart Langley liked Chris Clay's photo
12 hours ago
David Butler replied to David Butler's discussion How would you insulate this roof?
"Stuart, I wasn't considering the copula windows... yes, those would indeed need to be…"
13 hours ago
Stuart Langley replied to David Butler's discussion How would you insulate this roof?
"Well, @David Butler, you have seen the property more accurately than I have, but my impression of…"
13 hours ago
David Butler replied to David Butler's discussion How would you insulate this roof?
"@ Stuart,I don't think there's any concern about impact of 4" build-up on elevation…"
14 hours ago
Stuart Langley replied to David Butler's discussion How would you insulate this roof?
"So this building has a few issues with air leaks and air leaks have so much to do with discomfort…"
15 hours ago
Stuart Langley replied to David Butler's discussion How would you insulate this roof?
"John Hatfield has the right idea here for a new roof deck. Polyiso boards always need a good stout…"
15 hours ago

Photos

  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service