Can anyone recommend a low cost method for dealing with square recessed lights?   We find them often in soffits above kitchen sinks on eave exterior walls. In our experience:

  • There usually isn't enough head room to build a drywall or cement board box around them.
  • The prefabricated covers don't leave enough clearance around the larger housings and the headroom factor often prevents sealing covers anyway.
  • We've replaced the units with air-tight housings but they are expensive, often require new expensive trim, and since we can't find remodel housings, the headroom makes installing them very difficult.
  • We've also replaced them with surface mounts but that usually involves installing a junction box to extend the wiring, patching the ceiling hole, and drywall finishing since the surface mounts haven't been wide enough to cover the old hole.

Has anyone found air-tight inserts to fit square lights?  What about air-tight remodel housings?  Other suggestions?

Tags: Air, Lights, Recessed, Sealing

Views: 2820

Reply to This

Replies to This Discussion

I don't think there is an easy answer for this. It might be cheaper to cut it out and replace with a can IC AT can and do the repair.

The other idea which I do not even know if I would recommend it is to remove the trim cover remove the glass spray paint the trim replace the bulb with an LED caulk or silicone the glass to the trim and caulk the trim to the drywall.

you mitigate air but not insulation. the unit itself is still functioning as it was but is now airtight. 

I like your second idea although there is still a fire hazard potential if we insulate around the fixture and someone replaces the bulb in the future.

agreed

Can you create an air barrier (5/8" drywall or 1/2" ply) at the ceiling level? eliminating the soffit, and the need to air seal, baffel, and insulate around the fixture?

This makes allot of sense access in those areas is always tight but if it could be done it makes everything easy.

As I mentioned with sealing the light and you point out lack of the ability to insulate is an issue. I would not insulate around it, but in the future will others show this reservation? The bulb would not bother me as the fixture has not been altered significantly and can still bleed heat into attic space. Will whomever cuts the caulking to access the bulb reseal it? Unknown and therefore not the best solution long term.

However as a cheap way to stop convection thermal bridging it works. Radiant is another story of course.

At times during these processes we need to weigh what is the best way and explore less effective methods based on budget.

for cost effectiveness and speed Georges suggestion is the best one. 

If it was my house, I'd be completely comfortable with the LED and insulating over the housing.  In fact, I'm debating offering it as a solution for clients so long as they are willing to accept the risk.  In this case, the days of incandescent lighting are numbered so the future risk is pretty negligible.

I think we try too hard to make everything idiot proof and risk free...it limits options and makes jobs too expensive.  Our window of opportunity to prevent climate catastrophe is short.  We need to make weatherization more affordable and part of that may require clients to accept some responsibility.  That could mean they can choose to have insulation blown over LED converted light housings, forgo dams around unused chimneys, have their house tightened beyond BPI standards without having to install continuous ventilation, streamline combustion safety to backdraft tests under normal conditions, etc.  Who's house is it anyway?

That's our standard approach but it's just too difficult in the eaves with a 3/12 pitch roof.

always hard to solve what you cannot see.

I use a method which for lack of a better term I call a Popsicle in tight areas such as this. I cut a piece plywood or drywall wide enough to cover most of the hole but slim enough to get between rafters. The length long enough to cover the hole plus about six inches. I attach a 1 x 2 to the board long enough to push to the edge on one side or the other which ever has better access. I crawl to the space bringing caulk, mastic or foam with me and a screw gun and some screws. Once I get to the area I load up the edges and run a bead on the far side as close to the opening as I can. I push the piece as far to the plate as I can squish down with stick and then run a screw into the Popsicle handle to secure it to the ceiling joist

It is not perfect but is ready for blown in insulation now.

I think, LED caulk is one of the alternative and best option which will be suitable for our budget. As per your interest you may select it. If I found any alternative options, I inform you at any time.

led reflector design

Extend the wire, remove box, insulate and use track wiring?  move to round recessed lights,   or look at some of the 2'x2' LED panels....

RSS

Forum Discussions

Efficiency of furnace

Started by Jignesh in General Forum. Last reply by Eric Kjelshus 5 hours ago. 6 Replies

Insulation Blower Recommendations?

Started by Jim Conlon in General Forum. Last reply by Cameron Home Insulation 5 hours ago. 2 Replies

2005 EPAct tax credit

Started by Mandy Leazenby in General Forum. Last reply by Sean Lintow Sr on Thursday. 3 Replies

Best brands for furnace

Started by Jignesh in General Forum on Tuesday. 0 Replies

Latest Activity

Eric Kjelshus replied to Jignesh's discussion Efficiency of furnace
"I like looking at system efficiency - Lets say the you have a 95% gas using furnace 100,000…"
5 hours ago
Cameron Home Insulation replied to Jim Conlon's discussion Insulation Blower Recommendations?
"Hi, Rent a Cellulose Insulation Blower from your local Home Depot. Get more information about…"
5 hours ago
Todd Abercrombie liked Barbara Smith's video
yesterday
Jim Hensen replied to Jignesh's discussion Efficiency of furnace
"Great question - what the efficiency rating means is one of the most common questions we we asked.…"
yesterday
Michael Schettine's blog post was featured

Framing production combined with air sealing

Building Tighter Homes with Gasketed FramingIf you follow our blog, you know that we talk quite a…See More
Friday
Profile IconMichael E and Jason Dion joined Home Energy Pros Forum
Friday
Jason Dion joined Sean Lintow Sr's group
Thumbnail

Best Practices (Residential)

Best Building, Retrofitting, or even Auditing Practices - what are they, what should change, what…See More
Friday
Jason Dion joined Michael Stuart's group
Thumbnail

INFRARED THERMOGRAPHY USERS

This group is dedicated to knowledge sharing and discussion of infrared thermography for building…See More
Friday
Jason Dion joined allen p tanner's group
Thumbnail

Energy Auditing Equipment for Sale, Trade or to Purchase

Discuss the pros and cons of the equipment you are interested in prior to purchase. Post equipment…See More
Friday
Jason Dion joined Allison A. Bailes III's group
Thumbnail

HVAC

HVAC design, Manuals J, S, T, & D, Duct leakage, Air flow, ENERGY STAR new home requirements,…See More
Friday
Jason Dion joined Bob Krell's group
Thumbnail

Healthy Indoors (IAQ)

The Healthy Indoors group is focused on indoor air quality (IAQ), mold, moisture control, radon,…See More
Friday
Jason Dion joined Building Performance Institute's group
Thumbnail

Building Performance Institute (BPI)

BPI is the nation's premier standards development, quality assurance and credentialing organization…See More
Friday
Jason Dion joined Diane Chojnowski's group
Thumbnail

Job Board

This group is for posting jobs related to all aspects of the home performance industry including…See More
Friday
Brad Cook replied to Jignesh's discussion Efficiency of furnace
"NO combustion based heating system can ever be 100% efficient, according to the Second Law of…"
Thursday
Brian Robinson commented on Barbara Smith's video
Thumbnail

How to get top performance from your furnace, air conditioner or heat pump

"So glad you highlighted the importance of air sealing & insulating the home form the bottom to…"
Thursday
Brian Robinson replied to Jignesh's discussion Efficiency of furnace
"You also may also want to account for the distribution losses as you move the heat from the…"
Thursday
Michael Schettine posted a blog post

Framing production combined with air sealing

Building Tighter Homes with Gasketed FramingIf you follow our blog, you know that we talk quite a…See More
Thursday
David Butler replied to Jignesh's discussion Efficiency of furnace
"Adding to Sean's comment... The reason a 90%+ furnace uses a PVC flue (as opposed to metal) is…"
Thursday
Barbara Smith's video was featured

How to get top performance from your furnace, air conditioner or heat pump

Video produced as part of our Minnesota heating and cooling system study. Seventhwave
Thursday
DesignTech posted photos
Thursday

Photos

  • Add Photos
  • View All

© 2018   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service