This project involves abandoning a chimney and replacing a Natural Gas HWH. They were going to go solar (with condensing direct vent back up), but after realizing how efficient the new generation HWH are, the savings of going solar are quite small, the payback after incentives is still longer than the service life of the components. 
Our decision is to just get the most efficient, durable natural gas HWH out there and forgo the added expense of solar thermal.

Currently there exists a conventional 50g, 40k BTU with an 89 FHR. The family of six has been well served by the capacity of this HWH. They currently have no space-heating requirements of the HWH.

I'm having a hard time finding a 95% or better efficient HWH in this size and capacity. The best units (listed below) seem to be much larger and often designed for space heating as well. They are not adverse to spending $2-$4k as long as there is real value.

They will probably be adding a 200 sq. ft. room addition in the next couple years. It's long side will face due south and passive solar heating opportunities abound. Maybe one of these larger WH with side mounted taps would be wise to provide for a radiant slab in the future addition? Is it wise to put radiant in a solar thermal mass? I have seen it done before locally, but never experienced it.
I have narrowed it down to: 
Bradford-Whites Residential Ultra High Efficiency Energy Saver (http://www.bradfordwhite.com/products2.asp?id=1&product_id=345).
Does anyone have experience with these units, recommendations of others, or a different strategy to offer?
Many Thanks!

Views: 404

Reply to This

Replies to This Discussion

RP,

I purchased a Polaris 95% WH 5+ years ago and am still waiting to connect it to my upcoming radiant /forced air hydronic/towel heater project.

My choice was savaged by a Berkeley contractor who suggested a similar condensing unit from AO Smith.

I only want an American unit (to create jobs in the industrial sector) so I am not interested in what I'm sure are top quality Euro units.

My other plumber told me about some AO Smith shoddy workmanship regarding a lack of welds (just one spot weld on the burner!) and no replacement parts on the entire west coast.

I'm still in a quandry about which units to use... but the Polaris 50 gallon unit is working great for me so far. Mfg in Tenn.

I look forward to seeing what our cohorts recommend.

GM

Another plumber, giving me a proposal for a 10,000 sf house with 25 family members had great things to say about "triangle tube" water heaters. These are used in radiater heating but can also do DHW and connect easily to their own solar preheaters.

 However, when making the proposal for another job He wants to install Lochinvar "98% efficient" water heaters.

I am curious what others think about these brands and which they deem the highest qualitiy. I'm looking for long-term efficient function w/o problems and US manufacture.

GM


Thanks for the input. I have narrowed it down to choosing between the Polaris and the Phoenix. Both are made in the USA and have stainless tanks, but the Phoenix is edging ahead due to reliability and refined technology as described by a few expert plumbers I know.

One question. With a very high FHR (2-3x the existing conventional), it would seem to me that one could do with a smaller tank size. Are there any online sizing tools that would account for this?

 

George- I am not familiar with the types or brands you mentioned.


Well, once again this has been a very valuable exercise. Between here and another forum, I have narrowed it down.

Only Polaris has .5" gas piping options. Otherwise, I would have chosen the Phoenix for the previously mentioned advantages plus the 316L stainless tank as apposed to the 444 Stainless- a minor difference, but noteworthy.

Thanks!

RSS

Forum Discussions

Too many Heat Pump Water Heaters in a basement?

Started by Brad Cook in General Forum. Last reply by David Butler 18 hours ago. 9 Replies

How would you insulate this roof?

Started by David Butler in General Forum. Last reply by David Butler 19 hours ago. 2 Replies

Dirty solar panels

Started by Evan Mills in General Forum. Last reply by Stacie Bagnasco yesterday. 1 Reply

Fixing a water heater?

Started by John Shillito in Best Practices. Last reply by Eric Kjelshus on Friday. 21 Replies

Latest Activity

Profile IconTroy Spindler, Mike Berg, Andrew McDowell and 4 more joined Home Energy Pros Forum
11 minutes ago
David Butler replied to Brad Cook's discussion Too many Heat Pump Water Heaters in a basement?
"theoretically, let's say you perfectly isolate the HPWH from a heat source. The HPWH's…"
18 hours ago
David Butler replied to David Butler's discussion How would you insulate this roof?
"Interesting idea. Commercial roof on a slope! Typical density for roofing spray foam is 2.5 to 3.0…"
19 hours ago
Summer Redman added a discussion to the group Job Board
Thumbnail

Hiring 2 Training Specialists in Champaign-Urbana, Illinois

The Applied Research Institute (ARI) at the University of Illinois at Urbana-Champaign is seeking…See More
20 hours ago
Summer Redman joined Diane Chojnowski's group
Thumbnail

Job Board

This group is for posting jobs related to all aspects of the home performance industry including…See More
20 hours ago
Profile IconCrystal McLain, Robert Grindrod, Rich Wickman and 3 more joined Home Energy Pros Forum
yesterday
Stacie Bagnasco replied to Evan Mills's discussion Dirty solar panels
"This is a great idea. I clicked on your discussion because it made me remember that I forgot to get…"
yesterday
Kirsten Richnavsky posted an event
Thumbnail

rCloud - The Future of Testing at Your Office or Home

October 18, 2017 from 2pm to 3pm
Integrating rCloud as an essential part of your RESNET QA process.Retrotec’s rCloud app is here,…See More
yesterday

Photos

Loading…
  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service