I just wrapped up a quality assurance site inspection where I heard something unusual. The homeowner had a new furnace & central air conditioning system installed in November.  Since then he's been hearing a lot of interference on his AM radios in the house and his hunch is that it is somehow related to the installation of the furnace. I'm not well versed in radio frequency transmission, so I didn't have any clue about what could be causing this phenomenon.

Has anybody else come across this issue with new furnace installations? 

Cheers,

-Nick

Tags: air, conditioning, furnace, radio, weird

Views: 1822

Reply to This

Replies to This Discussion

Does it do it all the time or just when the furnace runs? Can you identify when in the firing sequence the noise starts?

I believe it happens whenever the blower motor is running.

If you Google RFI aka radio frequency interruption, you will find a lot of good info on it. Like Bob says, is it all the time or just when the furnace is running - do the have fluorescents nearby or neon lights, was any other work done? Depending on the exact source & cause of the problem, they maybe able to install a noise filter, while in other cases that won't work

If you try a battery powered AM radio and still have the problem, that eliminates the power as the source of the noise. All electronic devices have emission limits, so I would be talking to those who installed it.

Bud

We've seen interference created by furnaces that causes problems with short-wave radios, but never AM. However, it sounds like a similar issue. There is typically a section in the installation manual that discusses radio interference, and offers suggestions specific to the brand/model to reduce this. If that doesn't work, contact the installer, and have them work with the manufacturer to help resolve the issue.

I have put in a 30 MF cap in line( hot to hot com to com) and took care of this it. Clean up the power or add a ground  or both.

If a ECM motor and has weak ground and the gas pipe is the ground  I have seen this make lines in TV's.    I took at 6' X 1/2" ground rod next to dirt floor crawl space.  Of if good ground at box run a new ground to furnace.  The new furnaces take a lot better ground- pre 1980 did not use ground , the flame rod uses earth ground to make the flame prove flame or  ground path is the flame so it takes a very good ground for new installs.    Test your ground with a thumper  or take a water hose and water your ground rod see it goes a way

I did a install next to radio station and got the wire less controlls to turn on and off with out need 

The AM radio works well - generally the older the better :-)   Older radios tended to have larger ferrite rod antennas.  That internal antenna also was very directional.  It meant that you could easily pinpoint appliance noise INCLUDING electrical arcing.

Older, less efficient furnaces typically use a split phase capacitor motors.  While they are not particularly the MOST efficient motors - they generate very little (if any) electrical noise.

As suggested by others - an amateur radio operator may be more sensitive to the noise - because they are trying to pick up very distant stations.  The same can be true for a home owner that lives off in the fringe areas of a radio station.

Electronically Commutated Motors (ECM) can easily be the source of the problem... but the manufacturer of the furnace should have addressed the noise problem as part of their design.  Virtually all electronic devices sold within the US must have FCC testing for emissions.  The furnace would have also.  The manufacturers normally solve this by making sure the motor is correctly shielded and grounded.  The furnace cabinet sides generally connect together (electrically) to provide additional shielding.  Finally the installation instructions should have required a good earth ground.  If the furnace isn't grounded - all the "high frequency" noise that is generated by the switching circuits in the motor and  the computer board on the furnace -- make their way along the power connection -- and the duct work is then used for the ground.  Duct work can make good antennas.  

Amateur radio operators often check for loose, poorly grounded appliances and duct work.

The other sources of noise - that could be related to the HVAC -- include electronic air cleaners - which would come on when there is air.. and possibly a UV sanitizing light.

If the furnace was installed properly and it is indeed the source of the noise - contact the manufacturers tech support (or have the installer do it.) This becomes a bit tricky because you need to find someone to take ownership of the problem.  Unless the furnace installer has seen this often - they may dismiss it.  The factory will want the installer to check their work, etc.... 

Easy way to get their attention is to use the AM radio - and see how it works outside the house.  If it has wiped out reception to just a radio station that is quite some distance away - there may not be a lot that can be done... replacing even an incandescent with a CFL would probably cause the homeowner the same problem.  

But on the other hand it is quite bad in the house AND only with the furnace on... it was installed properly and it has a ground, then I would hope the manufacturer would want to know and see.  This is where digital cameras on cell phones are handy.  You can capture what you see and forward if necessary to the manufacturer.

I'm not sure you would want to use a capacitor to solve the problem ... if the noise is from the motor  it might be just a simple snap on RF ferrite choke...  see: http://www.rfparts.com/fercke-aaa.html 

But before I would even use the choke,  I'd put in a call to the manufacturer... it could be a known problem and they very well might have suppression kits that they want you to use.

The same rules about checking for grounding apply to the electronic air filters and UV sanitizers.  It may even be possible (not likely) a new fancy communicating thermostat is causing the problem.  That could be fixed by making sure that the wire is either shielded (and grounded at the furnace) or is twisted pair.

Hi Dennis, nice job covering all of the issues. It has been many years since I used an AM radio to locate some electronic noise, and you are correct, the older ones are better. :-)

Bud

Thanks everybody! I will send this thread along to the homeowner and hopefully he solve this mystery. When I get additional information I'll be sure to update you all.

Cheers!

RSS

Forum Discussions

Overheating garage

Started by Chris Bellanca in Best Practices. Last reply by Sean Lintow Sr on Friday. 2 Replies

E&O Insurance

Started by Rob Madden in General Forum on Thursday. 0 Replies

GSHP for domestic hot water

Started by David Holtzclaw in General Forum. Last reply by David Holtzclaw on Thursday. 3 Replies

Log home roof insulation

Started by Bob Reuther in Best Practices. Last reply by Daniel Baur-McGuire on Tuesday. 8 Replies

Latest Activity

Franco Oyuela commented on John White's blog post It’s Time to Replace Your Old Furnace and Air Unit with HVAC System
"Gas furnaces are one of the most energy efficient home comfort solutions you can have installed…"
35 minutes ago
Profile IconDavid Dennis, Lamont Goldstein, Trenton Fluetsch and 6 more joined Home Energy Pros Forum
1 hour ago
Michael Dunseith posted a status
Friday
CEE posted a blog post
Friday
Sean Lintow Sr replied to Chris Bellanca's discussion Overheating garage
"There are only two methods - block the heat before it gets in & exhaust what gets in Blocking -…"
Friday
John White posted photos
Friday
John White posted a blog post
Friday
Rob Madden posted a discussion

E&O Insurance

Any recommendations for a good E&O and general liability insurance carrier for energy…See More
Thursday
John Redmond added a discussion to the group Energy Auditing Equipment for Sale, Trade or to Purchase
Thumbnail

Flir I7 Infrared Camera (Barely Used)

I have been away from this site for a while, so my apologies if this is supposed to be posted…See More
Thursday
John Redmond joined allen p tanner's group
Thumbnail

Energy Auditing Equipment for Sale, Trade or to Purchase

Discuss the pros and cons of the equipment you are interested in prior to purchase. Post equipment…See More
Thursday
Hannah Wood liked Quinn Korzeniecki's discussion Application Period for 2018 Energy Auditor (EA) and Quality Control Inspector (QCI) Pilots Now Open
Thursday
Quinn Korzeniecki posted a discussion

Application Period for 2018 Energy Auditor (EA) and Quality Control Inspector (QCI) Pilots Now Open

We need you!Applications are now being accepted to participate in the 2018 Energy Auditor (EA) and…See More
Thursday
Quinn Korzeniecki added a discussion to the group Building Performance Institute (BPI)
Thumbnail

Application Period for 2018 Energy Auditor (EA) and Quality Control Inspector (QCI) Pilots Now Open

We need you!Applications are now being accepted to participate in the 2018 Energy Auditor (EA) and…See More
Thursday
David Butler replied to Chris Bellanca's discussion Overheating garage
"Easy... insulate the attic ceiling. I'm not sure how much good it would do to air seal a…"
Thursday
Chris Bellanca posted a discussion

Overheating garage

Hi all, I'm looking for potential solutions to a problem at a client's house.  The south facing 2…See More
Thursday
Landon added a discussion to the group Energy Auditing Equipment for Sale, Trade or to Purchase
Thumbnail

Brand new retrotec blower door system $3000

Hi, I’ve got a brand new blower door system from retrotec that I got 2 months ago, and never got…See More
Thursday
David Holtzclaw replied to David Holtzclaw's discussion GSHP for domestic hot water
"Thanks John & Bill. Bill your experience is one reason why I wanted a larger heat pump with…"
Thursday
Diane Chojnowski posted events
Wednesday
Rob commented on Bob Krell's group Healthy Indoors (IAQ)
"Hello, Has anyone tried custom filtering of window AC units? Specifically concerned with…"
Wednesday
Michael Dunseith's 2 photos were featured
Wednesday

Photos

  • Add Photos
  • View All

© 2018   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service