Measuring fresh air intake ducted to a return and no way of measuring from outside.

I am sure this is a challenge that some of you have faced before:

You have an air handling system with fresh air intake that is ducted into the return and is terminated on the outside in a way that would not allow you to measure it with a flow pan. 

My thinking is that there should be a way to measure the air flow by measuring pressure difference between outside and the fresh air duct and perhaps some more variables, like the size of the pipe and it's lenght.

I found some formulas and tried to do calculations using them but did not get the most realistic results. 

Or maybe there are some clever ways of measuring it using some common home performance tools?

Your suggestions? 

Attached is a picture of the particular system I am testing that has a huge (12" pipe) fresh air intake. 

Views: 3208

Attachments:

Reply to This

Replies to This Discussion

Others have given good ideas for roughly measuring the actual airflow. If I had a bit of time to kill, and the freedom to experiment with the house, I would probably seal the exterior inlet of the fresh air duct and then measure any changes in external static pressure and the RH% of the house. At 12" it's a lot larger than any I've ever seen on a residential system, and I've also seen a lot of them on houses that didn't seem tight enough to need them. 

Wow, just looked at the picture!  

Jack, you sure that's a fresh air intake?  Looks like 16" duct - and it's got a Carrier Infinity Zone Control damper on it.  I guess the Infinity might be managing fresh air, the thing is really complex.  

Since Jack hasn't responded to my "why" question, I suspect John Semmelhack's suspicions around 1 or 2 are correct.

1) Required for Energy Star 3.0 certification

2) Code compliance

Measuring airflow while the unit is operating will tell next to nothing unless you know at what static that fan will operate, and for how many hours.  Since it's an ECM unit likely with variable flow rates in both heating and cooling cycles, I think John Nichols answer is the only one that will tell you much. 

JS, be cautious committing too fervently to these fabrications:

3) Ensure there's enough airflow to help ensure healthy indoor air quality

4) Ensure there's not too much airflow to provide good energy efficiency 

"enough" and "too much" are complete abstractions attempting to tie to an unmeasured metric using "universal averages" that have a tremendous amount of deviation.  We need to make the word "ignorant" not have such bad connotations.  

Have you ever measured indoor air quality?  I have.  It make me realize that without CONTINUOUS measurement I am completely ignorant of it's "good"ness or "bad"ness.  ACH may be the best we can do for now, but let's not drink the cool aid and ascribe words like "Ensure" to IAQ.  That implies certainty we do not have, provides assurances that may prove fraudulent  and in my eyes is a path to appearing stupid and incompetent.     

The more we kid ourselves that we can "know" indoor air quality without actually measuring indoor air quality, the more we move from from science to religion.  From believers in data to dogma.  From ignorance to stupidity.  From ethical to unethical.  This bad information will eventually become persistent belief that causes harm.  Do no harm.  

Might it not be better to be honest about our ignorance than to make assurances we have no intention of measuring or proving?  Or are we just used car salesmen, saying what it takes to close the deal? 

Ted,

That is a sealed combustion furnace. We don't know what the hot water heater is. 

If that is someones idea of mechanical ventilation to meet ES 3.0, I believe they missed a class somewhere. Code compliance for fresh air in this area is required to be ducted into the return. This is not.

We need more info.

John N, the huge duct on the left with the blue zone control apparently ducted into a "bottom" return (bottom of the picture) 

"...fresh air intake that is ducted into the return..."

I don't think anyone was referring to combustion make up air.  I think this is about meeting building airflow standards with mechanical ventilation. 

Ted,

Thanks.  I had to pull the image of and lighten it up to make out the details down there.  It looked like a duct with no bottom in the original.

Sure John.  

Have you ever seen such a huge intake?  And so close to the unit.  LOT of air!  Not worried about shocking the heat exchanger?  Unlike an ERV, I would think you absolutely would NOT insulate that duct.

Where is this house? 

Any chance that duct is configured as some sort of "economizer"? A/C is not common here so I'm not familiar with all the permutations. What I usually see is a 4" or 6" duct from the exterior, with no means of controlling how much outside air is introduced into the airflow. Sometimes there's a mechanical damper that closes the duct when the fan is off, or a barometric damper.

Use a duct blaster as apowered flow hood, look in duct blaster manual.

That duct is an economizer. It's purpose is ventilation, and possibly cooling (rather than using the AC). Night time cooling works great in the western states in many places, where it's dry, and the temperatures drop at night to below house temps.

12" is bigger that needed for ASHRAE 62.2 Ventilation, maybe they wanted more for "better" IAQ, at a conditioning cost! It's sized more like a small commercial project that I was at last week.

Attachments:

Rick Karg has instructions for using a pitot tube to assess airflow in ducts.

His website Residential Energy Dynamics includes a calculator to determine duct CFM.  It's fairly accurate, provided you have plenty of straight duct upstream from the point of measurement.

RSS

Forum Discussions

Too many Heat Pump Water Heaters in a basement?

Started by Brad Cook in General Forum. Last reply by David Butler 58 minutes ago. 9 Replies

How would you insulate this roof?

Started by David Butler in General Forum. Last reply by David Butler 1 hour ago. 2 Replies

Dirty solar panels

Started by Evan Mills in General Forum. Last reply by Stacie Bagnasco 8 hours ago. 1 Reply

Fixing a water heater?

Started by John Shillito in Best Practices. Last reply by Eric Kjelshus on Friday. 21 Replies

Latest Activity

David Butler replied to Brad Cook's discussion Too many Heat Pump Water Heaters in a basement?
"theoretically, let's say you perfectly isolate the HPWH from a heat source. The HPWH's…"
58 minutes ago
David Butler replied to David Butler's discussion How would you insulate this roof?
"Interesting idea. Commercial roof on a slope! Typical density for roofing spray foam is 2.5 to 3.0…"
1 hour ago
Profile IconRandy Kinnison, Breanna Detwiler, Jeff Farlow and 7 more joined Home Energy Pros Forum
2 hours ago
Summer Redman added a discussion to the group Job Board
Thumbnail

Hiring 2 Training Specialists in Champaign-Urbana, Illinois

The Applied Research Institute (ARI) at the University of Illinois at Urbana-Champaign is seeking…See More
2 hours ago
Summer Redman joined Diane Chojnowski's group
Thumbnail

Job Board

This group is for posting jobs related to all aspects of the home performance industry including…See More
2 hours ago
Stacie Bagnasco replied to Evan Mills's discussion Dirty solar panels
"This is a great idea. I clicked on your discussion because it made me remember that I forgot to get…"
8 hours ago
Kirsten Richnavsky posted an event
Thumbnail

rCloud - The Future of Testing at Your Office or Home

October 18, 2017 from 2pm to 3pm
Integrating rCloud as an essential part of your RESNET QA process.Retrotec’s rCloud app is here,…See More
8 hours ago
Ed Whitaker replied to Brad Cook's discussion Too many Heat Pump Water Heaters in a basement?
"Brad,   I agree with the comments and would add a couple of thoughts. 1st,  any time you…"
8 hours ago

Photos

Loading…
  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service