Most boilers come with a manufacturer’s warranty. But after a few years, we experience some common boiler problems. Such problems can be addressed without the need to call a heating engineer; others will require the services of a qualified and experienced professional.

If the boiler feed water contains impurities beyond the prescribed limits they lead to the following problems.

1. (a) priming (b) foaming (c) carry over
2. Boiler corrosion
3. Scale sludge and formation
4. Caustic embitterment

1. Priming Foaming and Carry Over: when steam is produced rapidly in the boiler some small droplets of the liquid water are carried along with the steam. The steam with some small water droplets is called “wet steam “.
(a) Priming: The process of formation of wet steam is called priming. Priming also starts when level of water rises due to foaming. So priming is generally associated with foaming.
(b) Foaming: The formation of foam or bubbles at the water surface in boilers is called foaming which does not break easily.
(c) Carry over: The phenomenon of carrying of water along with impurities by steam is called “carry over”. This is mainly due to priming and foaming. Priming and foaming mainly occur together.

2. Boiler corrosion: The “decay” or “disintegration” of boiler material either by a chemical or electrochemical reaction with its environment is known as “Boiler corrosion“.

3. Sludge and scale formation: Boilers are used for steam formation. When hard water is continuously evaporated in boilers, the continuous evaporation of water increases the concentration of dissolved salts until the water becomes saturated. Then the salts of Ca++ and Mg++ along with other soluble impurities are precipitated on the inner walls of boilers. When the precipitate formed is soft, slimy and loose, known as sludge and is hard and firmly adhering on the inner walls of boilers, known as scale.

4. Caustic embrittlement: This is the phenomenon during which the boiler material becomes brittle due to the accumulation of caustic substances. It is form of corrosion caused by high concentration of sodium hydroxide in boiler water. It is most likely to occur in boilers operating at high pressures, where NaOH is produced in the boiler by the hydrolysis of some residual Na2CO3 obtained from water softening process like lime soda.

 Na2CO3 + H2O = 2NaOH + CO2

The formation of NaOH makes the boiler water caustic. This caustic water penetrates into the minute hair cracks present in the inner side of boiler by capillary action. When the water evaporates and the concentration of dissolved NaOH increases progressively which attracts the surrounding area, thereby dissolving the iron of boiler as sodium ferrate.

Fe + 2NaOH = Na2FeO2 + H2O

Original source - Boilers

Tags: Boiler, Boilers, boiler, caustic, corrosion, issues, priming, water

Views: 184

Reply to This

Replies to This Discussion

The comments appear to be directed more at commercial steam systems, but there is no question that water quality is starting to become a major issue with hydronic systems as well. Here in Vermont, and New England, the use of boilers and hydronic heating is much more common than the rest of the nation, and the water quality of private water sources (drilled wells and springs) varies very widely. Many heating contractors are not paying attention to water quality and with the advent of IFCs (internal flow checks) and the more complex condensing boilers, homeowners are starting to pay the price.

I recently had two calls for no heat just days apart. One was a mid-efficiency low mass boiler, about 10 years old, and the other was a high efficiency condensing boiler, which last year replaced a similar mid-efficiency low mass boiler. Both systems are propane-fired and both have a mixture of radiant and baseboard heating. In both cases, the IFC in a circulator for a radiant zone had become so clogged with rust that there was no flow at all. In the first case, the pressure indicator on the tridicator was completely blocked and the mixing valves had corroded to the point of no longer operating.

It is imperative that heating contractors pay attention to the water quality of water going into their boilers, including makeup feed water, and that they periodically test the boiler water and condition it as needed.

RSS

Latest Activity

Chris Dorsi posted an event
Thumbnail

2018 Habitat X Summer National Conference at Big Sky Montana

June 27, 2016 to June 29, 2016
The 2018 Habitat…See More
23 minutes ago
Stuart Langley liked David Byrnes's blog post Strategies for Hiring and Interviewing for Home Performance Professionals
4 hours ago
Kevin Miller replied to Bob Krell's discussion What Do You Do When You Find Suspected Mold? in the group Healthy Indoors (IAQ)
"Visual inspection can only confirm the presence of mold, not the absence.   That said,…"
7 hours ago
Armand C Magnelli replied to Don Fugler's discussion joining ducts in the group HVAC
"I often suggest pop-rivets as an alternative to sheet metal screws for both clothes dryer duct work…"
7 hours ago
Kevin Miller replied to Bob Krell's discussion What Do You Do When You Find Suspected Mold? in the group Healthy Indoors (IAQ)
"Sampling would be primarily to verify 'Condition 1' or 'Normal Fungal Ecology'…"
7 hours ago
Daniel Cullen joined Building Performance Institute's group
Thumbnail

Building Performance Institute (BPI)

BPI is the nation's premier standards development, quality assurance and credentialing organization…See More
7 hours ago
Daniel Cullen replied to Bob Krell's discussion What Do You Do When You Find Suspected Mold? in the group Healthy Indoors (IAQ)
"Can anyone tell me exactly HOW mold sampling impacts the mold remediation process or protocol? Why…"
8 hours ago
Daniel Cullen joined Bob Krell's group
Thumbnail

Healthy Indoors (IAQ)

The Healthy Indoors group is focused on indoor air quality (IAQ), mold, moisture control, radon,…See More
8 hours ago

Photos

  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service