I am curious/concerned about advising a tight house (addition) with a cathedral ceiling. I understand that normally, one should keep a 1-2" gap in the rafter bay above the insulation as an air gap. But, if the construction is tight, to achieve a low ACH50 or 1-2, what is the point?How is air (moisture) going to escape if the enclosure, including the roof sheeting, is sealed tight? Also interestingly, the plans did not include any mandatory ventilation for this 780 sqft addition in So. Cal. by the ocean. 

Thank you. 

Dav  

Tags: Tight, control, enclosure, moisture

Views: 245

Reply to This

Replies to This Discussion

It depends, are they going with a hot roof system? If so no air gap is required

The reason for the gap is because even with super low leakage numbers, you still have leakage & the reason the bays get ventilated is to eliminate condensation issues with the sheathing

Most places will not require "ventilation" for additions as they assume the house has it already & it is not a mandatory no matter what if you do X you must put Y in like smoke detectors / carbon monoxide

I agree with Sean, that the main concern is condensation, and in northern climates frost accumulation in the attic.  In southern CA, I am sure those are not a big considerations. You should still have some low attic venting, but it is not as critical.  

Paul

With a vented cathedral ceiling, getting a tight envelope is difficult, but not impossible. Various products are available to maintain the vent gap, some of which are easier than others to air seal.

It's easier, and I believe better, to go with an unvented assembly, in which case the insulation must be fully in contact with the roof, and depending on climate zone, some portion must be air impermeable (less in milder climates, more in colder climates). The purpose is to prevent house moisture from coming in contact a cold roof.

House moisture is removed by spot exhaust in kitchen & baths. Whole house ventilation has a different purpose.

I'm not familiar with California Title 24 requirements for unvented roofs but here's a link to the IRC Chapter that covers that detail (scroll down to Section R806.5): IRC Chapter 8

It is all about the dewpoint. Think of the roof system as a big box. Air can circulate in, out and around the inside of that box. If you could possibly air seal the entire inside plane, and install a durable, continuous and effective vapor barrier over the entire inside plane, you still have the other 5 sides where air and/or moisture can enter (or leave) the box. When the outside temperature falls by a significant amount (as when it is cold enough for snow in the South), you are most likely to hit the dewpoint on those 5 sides. When that condensation pools up in the air permeable insulation, it will be difficult for that water to get out of there unless there is a reasonable connection for air to move in and out. By the time the water eventually gets out, it could promote the growth of fungi, such as wood rot. That is why we ventilate roofs. If there is enough air and vapor impermeable insulation on the roof deck, then the temperature inside the box should stay above the dewpoint and ventilation is not needed (or desired).

I would refer you to this document by Building Science Corp., which tackles the issue of ventilation in cathedral or flat roofs. You don't need to ventilate, but you need to carefully design the assembly.

https://buildingscience.com/documents/insights/bsi-043-dont-be-dense

"Why such a difference between walls and roofs? Walls in most older houses can dry out to the exterior because they rarely have exterior vapor barriers. Roofs have either roof membranes or asphalt shingles that are exterior vapor barriers, and they can’t dry out to the exterior unless the roof assembly is vented to the exterior. We have developed ways of dealing with unvented roof assemblies and insulation, but dense packing them is not one of them. I’ll talk more about the alternative ways later. Walls have “wiggle” room. We don’t have to be perfect because some drying can occur to the outside. We do not typically have the same “wiggle” room with unvented roofs."

RSS

Forum Discussions

Outdoor Reset

Started by Sean Wiens in HVAC 20 hours ago. 0 Replies

Best Energy Myths

Started by Silas Inman in Best Practices. Last reply by Liam Smith on Wednesday. 45 Replies

HERS score with HRV

Started by Gary Hall in General Forum. Last reply by John C. Semmelhack May 19. 4 Replies

Latest Activity

Sean Wiens posted a discussion

Outdoor Reset

Can some of you weigh in on what you feel is the best wired outdoor reset and why?  I am currently…See More
20 hours ago
Tom Phillips replied to Don Fugler's discussion Choosing a range hood in the group Kitchen Ventilation
"thx Don! re: Capture Efficiency, the ROÇIS Kitchen Range Hood document addresses what hood…"
yesterday
Dara Bowser joined Don Fugler's group
Thumbnail

Kitchen Ventilation

In many homes, cooking is the largest indoor source of air pollutants. Exposures can be higher in…See More
yesterday
Dara Bowser liked Don Fugler's discussion Choosing a range hood
yesterday
Profile IconChris Hawkins and Drew Brauer joined Home Energy Pros Forum
Saturday
Profile IconLauren Asplen and Danny Gough joined Bob Krell's group
Thumbnail

Healthy Indoors (IAQ)

The Healthy Indoors group is focused on indoor air quality (IAQ), mold, moisture control, radon,…See More
Friday
Franco Oyuela commented on John White's blog post What to Expect from a New HVAC Unit Installation Cost
"Is strongly advise against attempting to install any complex home comfort equipment on your own.…"
Friday
CEE posted a blog post
Friday
Lindsay Bachman liked David Keefe's video
Friday
Julie Saporito's blog post was featured
Friday
John C. Semmelhack liked Diane Chojnowski's discussion Everything you need to know about California's new solar roof mandate
Friday
Profile IconJohn Walter and Eric Rabesa joined Home Energy Pros Forum
Thursday
William Collins posted a video

The Foam Sealants Kit " Bead or Spray"

Now you can apply foam sealant as a " bead " or a " spray " with the Foam Sealants Kit. When using a 16lb Canister of Black Sealant you can easily go from us...
Thursday
Profile IconSean Wiens and Armando Cobo joined Don Fugler's group
Thumbnail

Kitchen Ventilation

In many homes, cooking is the largest indoor source of air pollutants. Exposures can be higher in…See More
Thursday
Julie Saporito posted a blog post
Thursday
Brennan Less replied to Linda Wigington's discussion Good Eating with Reduced Cooking Emissions in the group Kitchen Ventilation
"Cook outside, as much as you can, and close your doors/windows while you do it ;) "
Thursday
Ethan Foley joined Bob Krell's group
Thumbnail

Healthy Indoors (IAQ)

The Healthy Indoors group is focused on indoor air quality (IAQ), mold, moisture control, radon,…See More
Thursday
Shane S posted a photo
Thursday
Al Tibbs posted photos
Wednesday
Al Tibbs commented on Eric Aune's photo
Thumbnail

IMG00173-20100805-1030

"Always remind customer to make sure to mark out location of piping before covering!! The infrared…"
Wednesday

Photos

  • Add Photos
  • View All

© 2018   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service