When doing a blower door test, do you ever use long term average? Why or why not?

Digital pressure and flow gauges have an option for time averaging, such as 1, 5 or 10 seconds, long term or a manual time average option.

Under what circumstances would you use the long term average and why?

Views: 284

Reply to This

Replies to This Discussion

When the wind is breezy, I use long term averaging. The more the pressure jumps around due to breezes, the longer the term that I use. Even then, I mentally average the readings. This is after I have taken steps to shield the end of the outside hose from the wind.

Wind is caused by a difference in air pressure so the change in air pressure from the wind, or a passing truck, is reflected in the change in the readings of a digital pressure gauge. Keep in mind that 1 pascal is a tiny change of pressure. I find that the best way to get a stable baseline is to insert a "T" fitting into the reference tube and connect 2 reference tubes. Place 1 tube on 1 side of the house and the other tube on the opposite side of the house. Be sure that the tube nearest the blower door is at least 5' (preferably more) from the fan. If the fan needs to be installed where it is blowing into an enclosed porch or mud room (not a good choice unless there is no better alternative) make sure the tube is outside of the porch.

Hi Kim,

Wind is probably the most frequent reason for using the time averaging with our manometers, but there is another that we need to be careful with.  Manometers are unique in that they ignore barometric pressures.  Place your refer tube out the front door and walk your manometer (long tube) upstairs or into the basement and even though the top to bottom pressure may vary (on a cold day) by 50 pascals or more our manometers will register very little.  When the temperature of our tubes and the air inside is the same as in the house, any changes in elevation are canceled out.  However, if those tubes just came out of an ice cold vehicle, or a hot one, and have not fully acclimated, our readings will drift.  In this case, before we start averaging we need to allow those tubes to become room temperature.  The section of tube that goes outside needs to acclimate as well.

Bud

I never use any setting but "long term" average. Any other setting will always give you a less accurate average reading. Under the "long term" setting the manometer automatically calculates a mathematically continuous average. That means that you can "hold " the reading after "any" length of time and it will give the average for all of the seconds that you had the meter running.

RSS

Forum Discussions

Too many Heat Pump Water Heaters in a basement?

Started by Brad Cook in General Forum. Last reply by David Butler 20 hours ago. 9 Replies

How would you insulate this roof?

Started by David Butler in General Forum. Last reply by David Butler 21 hours ago. 2 Replies

Dirty solar panels

Started by Evan Mills in General Forum. Last reply by Stacie Bagnasco yesterday. 1 Reply

Fixing a water heater?

Started by John Shillito in Best Practices. Last reply by Eric Kjelshus on Friday. 21 Replies

Latest Activity

Profile IconTroy Spindler, Mike Berg, Andrew McDowell and 4 more joined Home Energy Pros Forum
1 hour ago
David Butler replied to Brad Cook's discussion Too many Heat Pump Water Heaters in a basement?
"theoretically, let's say you perfectly isolate the HPWH from a heat source. The HPWH's…"
20 hours ago
David Butler replied to David Butler's discussion How would you insulate this roof?
"Interesting idea. Commercial roof on a slope! Typical density for roofing spray foam is 2.5 to 3.0…"
21 hours ago
Summer Redman added a discussion to the group Job Board
Thumbnail

Hiring 2 Training Specialists in Champaign-Urbana, Illinois

The Applied Research Institute (ARI) at the University of Illinois at Urbana-Champaign is seeking…See More
22 hours ago
Summer Redman joined Diane Chojnowski's group
Thumbnail

Job Board

This group is for posting jobs related to all aspects of the home performance industry including…See More
22 hours ago
Profile IconCrystal McLain, Robert Grindrod, Rich Wickman and 3 more joined Home Energy Pros Forum
yesterday
Stacie Bagnasco replied to Evan Mills's discussion Dirty solar panels
"This is a great idea. I clicked on your discussion because it made me remember that I forgot to get…"
yesterday
Kirsten Richnavsky posted an event
Thumbnail

rCloud - The Future of Testing at Your Office or Home

October 18, 2017 from 2pm to 3pm
Integrating rCloud as an essential part of your RESNET QA process.Retrotec’s rCloud app is here,…See More
yesterday

Photos

Loading…
  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service