I'm glad to see LED fixtures finally becoming mainstream in the local big box stores. Purpose built fixtures make more sense than trying to make LED's look and work like A19 lamps. Here's an example of the fixture I saw at the local Home Depot today:

http://www.homedepot.com/p/Lithonia-Lighting-Versi-Lite-7-in-White-...

I'll post more photos/findings once I get it hooked up.

Tags: Fixture, LED, Light

Views: 1025

Reply to This

Replies to This Discussion

I too had the offset issue, the 2nd screw went direct into the ceiling joist. Oddly the smaller boxes seem more common than the larger ones in ceiling use.

There are 50 point LED's (possibly cree's devices) on the board.  The large black chip is most likely the a chip whose function is sensing dimming on the incoming power signal and translating that to the equivalent on/off duty cycle for the LED's.  Just a couple of small surface mount chip caps.. so no electrolytics to fail.  But heat is a silent killer for most IC's... if the fixture is hot - U1 is gets my second vote for the most failures.  First goes to the movistor.  The LED's are likely to suffer a "fading" effect and slowly become less effective. Four or five years from now you might notice a difference if you compare it against an identical fixture.  But then anyone expect a CFL last five years - with lots of use, dimming, and turning on/off....

At $30 I expect it to last, hopefully they stand behind their warranty for 5yrs if it doesn't. If it fails after 5yrs LED tech will be fully mature by then and newer better fixtures will be out. Fixtures designed for LED from the start have a lumen/watt advantage since they can take advantage of the native directional properties of LED. Fixtures also have more thermal management options compared to A19 retrofit laps, and as you said heat is the enemy of the electronics/driver circuit.

IMHO the best is yet to come for LED fixtures, I'm sure they are working on things we haven't even though of. Fixtures is what will revolutionize the LED lighting industry, not A19 replacements...

Generally based upon the needed requirements, The mode of selection will be depended. In these aspects, We must consider the high quality of LED strips which will help us to give more brightness while compared to the normal one.

reflector design

RSS

Forum Discussions

How would you insulate this roof?

Started by David Butler in General Forum. Last reply by John Hatfield 1 hour ago. 3 Replies

Psychrometric Chart Training

Started by John Krochmalny in Training 22 hours ago. 0 Replies

Dirty solar panels

Started by Evan Mills in General Forum. Last reply by Stacie Bagnasco on Monday. 1 Reply

Latest Activity

Crista replied to Brad Cook's discussion Too many Heat Pump Water Heaters in a basement?
"You might find this study of…"
16 minutes ago
Profile IconCrista, David Potter, Walter Neboshynsky and 3 more joined Home Energy Pros Forum
17 minutes ago
Lindsay Bachman's event was featured
Thumbnail

2017 HPC California Regional Home Performance Conference & Trade Show at Hilton Long Beach

November 14, 2017 at 7am to November 15, 2017 at 3pm
We are excited to join together with industry leaders along with fellow weatherization…See More
30 minutes ago
Joe Hughes's event was featured
Thumbnail

HEALTHY BUILDINGS SUMMIT 2017 Conference at Seven Springs Mountain Resort

November 2, 2017 to November 4, 2017
Join us for another year of outstanding "Research to Practice" presentations with world class…See More
31 minutes ago
Michael Duclos's event was featured
Thumbnail

Passive House Massachusetts - Symposium at District Hall, Boston, MA

October 25, 2017 all day
Getting High Performance Buildings DonePassive house standards and strategies have come a long way…See More
31 minutes ago
Diane Chojnowski's event was featured
Thumbnail

2017 Home Performance Coalition California Regional Home Performance Conference & Trade Show at Hilton Long Beach

November 14, 2017 to November 15, 2017
We are excited to join together with industry leaders along with fellow weatherization…See More
31 minutes ago
John Hatfield replied to David Butler's discussion How would you insulate this roof?
"The solution maybe installation of foam fill panels between the existing raised metal ribs within…"
1 hour ago
Marc Tannenbaum posted a blog post

3 Issues HVAC contractors Should Know About Impacting Customer Comfort and Health

There is an epidemic of people suffering in many of the 100 million homes across the U.S.  Many of…See More
1 hour ago

Photos

Loading…
  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service