Are there suggestions out there as to the best way to insulate newly installed speakers!  I have been working to improve the  tightness of my 22 year old home but after that big effort, I installed 10 speakers in 5 rooms.  This, as one might suspect, has resulted in several holes leading from unconditioned spaces to conditioned spaces. Some folks say just drape insulation over the new speakers while other say build a box to protect the innards of the speakers from fiber glass, dust, etc. The latter is supposed to enhance the quality of the music emanating from the speakers but there are many opinions out there!

Views: 24382

Reply to This

Replies to This Discussion

From techstreet -- holder of some of the UL documents.... about UL-1715

"This test method is intended for use in the evaluation of the flammability contribution of wall materia l assemblies, ceiling material assemblies, or both, exposed to early fire growth under specified room fir e exposure conditions. The effectiveness of fire barrier materials as protection for other combustible materials or components within the assembly is of primary interest for this evaluation."

The point of suggesting to look for UL1715 and the ASTM numbers is that it might be that other good building materials would be found that could do a better job for John.  That was the reason for suggesting keywords for searches.

The Tenmat hats themselves provide the flame spread,  the fire stop foams/sealants, just cover the cases where flames might seep under the hats and into the attic.   They also stop the hats from rattling and dancing around in the attic when loud rock and roll is played  :-)

good point on the dancing. 

my only concern is that folks dont get the impression there are fire safe foam's out there.  if you ignite an piece of FS 25 foam and take the flame source away, the foam will self extinguish.  But, the tech data sheets the foam manufacturers provide will have footnotes saying their foam requires a 15 minute thermal barrier between the foam and the people.  that's becasue foam has a low self ignition temperaturte, and it is very good at holding heat in.  it doesn't take long for foam to burn when it is exposed to heat in excess of 450 degrees. 

RSS

Forum Discussions

Home Energy Pros and #MeToo

Started by Mike Rogers in General Forum 10 hours ago. 0 Replies

How would you insulate this roof?

Started by David Butler in General Forum. Last reply by David Butler yesterday. 34 Replies

Psychrometric Chart Training

Started by John Krochmalny in Training. Last reply by Mahendra Shah on Friday. 1 Reply

Latest Activity

Blake Shurtz posted a discussion

Replacement for Energy Conservatory Flow-blaster

It's too bad that the flow-blaster is no longer being produced or technically supported. Does…See More
4 hours ago
Profile IconBrian Cizmar, Charles Allen, Charles Buell and 1 more joined Home Energy Pros Forum
7 hours ago
Mike Rogers posted a discussion

Home Energy Pros and #MeToo

If it doesn't seem obvious why a discussion of …See More
10 hours ago
David Butler replied to David Butler's discussion How would you insulate this roof?
"Sean Lintow proposed rails and clips (re: first comment in this discussion), but in the context of…"
yesterday
Brad Cook replied to David Butler's discussion How would you insulate this roof?
"I missed where the suggestion for rails came in. The plywood would not need any rails. 4+ inches is…"
yesterday
David Butler replied to David Butler's discussion How would you insulate this roof?
"I'm a little confused about the necessity and purpose of using support rails if working on…"
yesterday
David Butler replied to David Butler's discussion How would you insulate this roof?
"If you insulate master bedroom and family room from below, you definitely need more R-value than…"
yesterday
David Butler replied to David Butler's discussion How would you insulate this roof?
"Brad, I was only talking about using EPS between the ridges, if necessary, to conform to bolts.…"
yesterday

Photos

  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service