High Density Foam -- Any Incidents of Cracking in Frame Walls as Studs Dry/Twist?

Just had a convo with a cold climate builder who said he has had concerns about the viability of the continuity of the air/vapour barrier created by using high-density foam in frame walls where budget dictates non-kiln-dried framing materials. Once the foam has set, and the wood starts to dry out, he has seen the studs twist and cup and significant cracks develop at the junction between the studs and the foam, and in some cases throughout the foam itself.

Although he didn't tell me if he'd done a before/after blower door test to see what the delta, his concern was enough to make him change products. He now uses high density foam on all non-framed walls where there is no issue with movement or shrinkage and the more flexible low density foam on framed walls. He's willing to take the hit on the lower insulation value and the additional vapour barrier requirement.

I hadn't bumped into this issue before and wonder if there are more people who have experienced this problem, and if so, is there any documentation, and if not, do you think there should be?

Views: 319

Reply to This

Replies to This Discussion

...apart from installation issues, I mean. Have asked a few questions of one Net Zero builder who is using high-density foam and he pointed to installation QA/QC problems with +2" layers being sprayed, or layers are being sprayed without enough setting time between them if pulling and cracking are issues. He noted one incidence where a crap installation at the rim joists left gaps of 1 to 1.5 inches!

He didn't see much of an issue with air barrier being compromised, because spray foam would be in contact with sheathing and that is stable. I have a few phone calls with other Net Zero/Low Energy builders this week that are unrelated to this topic, but I know they have experience with high density foam, so I'll ask some more questions and report back on what I find.

Well if budget dictates one uses wet / green wood, said budget had better dictate drying time as no product should be installed until everything is dried out

The issue isn't the product, it is improper application

Shawna foam pulling away from the studs due to over application will cause spontaneous combustion or core burn. A poor mix will cause splitting of the foam and noxcious odors. See...

http://masonknowles.com/docs/troubleshooting_sprayfoam_insulation_j...

and

https://www.osha.gov/dte/grant_materials/fy10/sh-21003-10/manual.pdf

 

RSS

Forum Discussions

Psychrometric Chart Training

Started by John Krochmalny in Training 17 hours ago. 0 Replies

How would you insulate this roof?

Started by David Butler in General Forum. Last reply by David Butler on Monday. 2 Replies

Dirty solar panels

Started by Evan Mills in General Forum. Last reply by Stacie Bagnasco on Monday. 1 Reply

Latest Activity

David Butler replied to Brad Cook's discussion Too many Heat Pump Water Heaters in a basement?
"Hi Mike, it's good to get some feedback from the field, and thanks for confirming Gen 3 is now…"
6 hours ago
B Eric Bell liked Bob Krell's group Healthy Indoors (IAQ)
15 hours ago
John Krochmalny posted a discussion

Psychrometric Chart Training

Looking through the various areas of this site, I didn't see too much information or training on…See More
17 hours ago
Profile IconMike Malek, Avery T. Phillips and Sarah Burger joined Home Energy Pros Forum
18 hours ago
Dannie Jackson's blog post was featured

Core Heat And Other Concepts

  In some places the use of solar heated liquids from hot water solar panels are used to provide…See More
23 hours ago
Michael Duclos replied to Brad Cook's discussion Too many Heat Pump Water Heaters in a basement?
"I’ve been looking into Sanden for a multi-family PH near Laconia, NH, ASHRAE 99.6% temp is…"
23 hours ago
Profile IconTroy Spindler, Mike Berg, Andrew McDowell and 4 more joined Home Energy Pros Forum
yesterday
David Butler replied to Brad Cook's discussion Too many Heat Pump Water Heaters in a basement?
"theoretically, let's say you perfectly isolate the HPWH from a heat source. The HPWH's…"
Monday

Photos

Loading…
  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service