High Density Foam -- Any Incidents of Cracking in Frame Walls as Studs Dry/Twist?

Just had a convo with a cold climate builder who said he has had concerns about the viability of the continuity of the air/vapour barrier created by using high-density foam in frame walls where budget dictates non-kiln-dried framing materials. Once the foam has set, and the wood starts to dry out, he has seen the studs twist and cup and significant cracks develop at the junction between the studs and the foam, and in some cases throughout the foam itself.

Although he didn't tell me if he'd done a before/after blower door test to see what the delta, his concern was enough to make him change products. He now uses high density foam on all non-framed walls where there is no issue with movement or shrinkage and the more flexible low density foam on framed walls. He's willing to take the hit on the lower insulation value and the additional vapour barrier requirement.

I hadn't bumped into this issue before and wonder if there are more people who have experienced this problem, and if so, is there any documentation, and if not, do you think there should be?

Views: 319

Reply to This

Replies to This Discussion

...apart from installation issues, I mean. Have asked a few questions of one Net Zero builder who is using high-density foam and he pointed to installation QA/QC problems with +2" layers being sprayed, or layers are being sprayed without enough setting time between them if pulling and cracking are issues. He noted one incidence where a crap installation at the rim joists left gaps of 1 to 1.5 inches!

He didn't see much of an issue with air barrier being compromised, because spray foam would be in contact with sheathing and that is stable. I have a few phone calls with other Net Zero/Low Energy builders this week that are unrelated to this topic, but I know they have experience with high density foam, so I'll ask some more questions and report back on what I find.

Well if budget dictates one uses wet / green wood, said budget had better dictate drying time as no product should be installed until everything is dried out

The issue isn't the product, it is improper application

Shawna foam pulling away from the studs due to over application will cause spontaneous combustion or core burn. A poor mix will cause splitting of the foam and noxcious odors. See...

http://masonknowles.com/docs/troubleshooting_sprayfoam_insulation_j...

and

https://www.osha.gov/dte/grant_materials/fy10/sh-21003-10/manual.pdf

 

RSS

Forum Discussions

Too many Heat Pump Water Heaters in a basement?

Started by Brad Cook in General Forum. Last reply by David Butler 10 hours ago. 9 Replies

How would you insulate this roof?

Started by David Butler in General Forum. Last reply by David Butler 11 hours ago. 2 Replies

Dirty solar panels

Started by Evan Mills in General Forum. Last reply by Stacie Bagnasco 17 hours ago. 1 Reply

Fixing a water heater?

Started by John Shillito in Best Practices. Last reply by Eric Kjelshus on Friday. 21 Replies

Latest Activity

Profile IconAndrew McDowell, Randy Kinnison, Breanna Detwiler and 8 more joined Home Energy Pros Forum
8 hours ago
David Butler replied to Brad Cook's discussion Too many Heat Pump Water Heaters in a basement?
"theoretically, let's say you perfectly isolate the HPWH from a heat source. The HPWH's…"
10 hours ago
David Butler replied to David Butler's discussion How would you insulate this roof?
"Interesting idea. Commercial roof on a slope! Typical density for roofing spray foam is 2.5 to 3.0…"
11 hours ago
Summer Redman added a discussion to the group Job Board
Thumbnail

Hiring 2 Training Specialists in Champaign-Urbana, Illinois

The Applied Research Institute (ARI) at the University of Illinois at Urbana-Champaign is seeking…See More
12 hours ago
Summer Redman joined Diane Chojnowski's group
Thumbnail

Job Board

This group is for posting jobs related to all aspects of the home performance industry including…See More
12 hours ago
Stacie Bagnasco replied to Evan Mills's discussion Dirty solar panels
"This is a great idea. I clicked on your discussion because it made me remember that I forgot to get…"
17 hours ago
Kirsten Richnavsky posted an event
Thumbnail

rCloud - The Future of Testing at Your Office or Home

October 18, 2017 from 2pm to 3pm
Integrating rCloud as an essential part of your RESNET QA process.Retrotec’s rCloud app is here,…See More
17 hours ago
Ed Whitaker replied to Brad Cook's discussion Too many Heat Pump Water Heaters in a basement?
"Brad,   I agree with the comments and would add a couple of thoughts. 1st,  any time you…"
18 hours ago

Photos

Loading…
  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service