I am building three houses in eastern Alabama and using the Earth cents program. I wanted to go with energy star but could not find a heat and air contractor to do it. My first house is about ready for testing and I think I have it sealed pretty good but am curious as to what I may have missed. Is there any classic areas of leakage that I am not aware of. I have looked online and can find no checklists or anything. I am from central Fl. so I have a good handle on the obvious for HVAC been using mastic for years.

Views: 437

Reply to This

Replies to This Discussion

Your rater should have gone over this with you before the drywall went up (better yet at the design phase), but here is the Energy Star one...

http://www.energystar.gov/ia/partners/bldrs_lenders_raters/download...

Based on the pics I have seen - slab to frame connection and you are going to have some fun with the roof & tray area - you don't have a crawl so that eliminates a bunch

As an FYI, last I checked there are 3 contractors in Alabama which doesn't include those in Georgia that do ES HVAC

For your reading pleasure - air sealing & insulation articles / ducts only

Yes the rater that Alabama power suggested I go with has done all that and did a pre-drywall inspection.I was just wondering about little trade secrets things I should watch for. As for ES contractors I called all on the list and none were even interested in even bidding guess Annisiton is to far to drive. I am sure I could make it worth someones while but I still have to compete with traditional builders here. Until the appraisers start adding value to this it is going to be a tough sell.

Smoke and blow.


After you clear your mind of whatever mental image that conjures, find an energy auditor with a blower door kit and a theatrical smoke (fog) machine (you may have to rent, beg, borrow or steal the fogger)


Subs whose scope encompasses air sealing activity may yawn and shrug at flickering digits on a blower door computer...thinking "what me worry?"

When those same clowns see smoke pouring from whatever assembly they "sealed", they'll spit out their chew, step up and git 'er done.

It is not that bad around here no one I know chews. We have been using a halogen light at night inside with someone in the attic it has been illuminating to say the least. The air tight fixtures were not so air tight after all. I glued all the drywall at top plate and that seemed to work and going to silicone base to slab and so forth. What was funny is Ac guy used mastic but without mesh tape and wondered who pulled the insulation off when it slipped down. Going to be a long winter.   I will see if party store has smoke machine.

go to a dj store for a smoke machine they have better one than the party store

Beware cheap smoke machines - may leave an oily film. That may not be a concern for rough-in testing, but our work involves retrofits to occupied homes, so we use a Hollywood-grade glycol-fueled machine by Rosco.

Look for a Rosco or similar unit for rental.

RSS

Latest Activity

Don Fugler replied to Don Fugler's discussion joining ducts in the group HVAC
"David, If the IMC mandates metal dryer duct and prohibits metal screws, they must be accepting…"
44 minutes ago
David Butler replied to Don Fugler's discussion joining ducts in the group HVAC
"I never checked that before. Checking now... Section M1502.4.2 of the International Residential…"
55 minutes ago
Joseph Frasier is now a member of Home Energy Pros Forum
55 minutes ago
Don Fugler replied to Don Fugler's discussion joining ducts in the group HVAC
"Brendan, Thanks for that response. Because of your warning, I just went down to the basement and…"
4 hours ago
Brendan Reid replied to Don Fugler's discussion joining ducts in the group HVAC
"Hi Don, Summary: DRYER VENT: screws bad idea, possibly prohibited by code. METAL DUCT: must be…"
5 hours ago
Profile IconBrendan Reid and David Butler joined Allison A. Bailes III's group
Thumbnail

HVAC

HVAC design, Manuals J, S, T, & D, Duct leakage, Air flow, ENERGY STAR new home requirements,…See More
5 hours ago
Profile IconSean Wiens and David Butler joined Chris Laumer-Giddens's group
Thumbnail

Energy Efficient Design

Energy efficiency starts at the drafting table...How architects and designers can help buildings…See More
13 hours ago
Profile IconSean Wiens and David Butler joined Mark Richardson's group
Thumbnail

Renewable Energy

This group will focus on the issues associated with incorporating renewable energy sources like…See More
13 hours ago

Photos

  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service