HELP - AIR SEALING a Continuous Stone Interior/ Exterior Wall

I just recently audited a home that had a blower door number of 11,684 CFM50 and/or 11.81 ACH50. And of course one of the main air infiltration culprits was a stone face wall that was continuous on the outside and inside of the building envelope. The basics as I see it is this: the 1/4" stone joints allow air to freely flow into the house.

Does anyone know of any good methods to seal a high-end stone wall air leakage like this? 

Thanks.

Below are some photos:

PHOTO OF HOUSE Stone Wall Located Bottom Right

CLOSEUP PHOTO OF HOUSE Stone Wall / Back Exterior Door (OUTSIDE)

INFRARED/ ACTUAL Stone Wall/ Back Exterior Door (INSIDE)

INTERIOR WALL - INFRARED / ACTUAL



Views: 4065

Reply to This

Replies to This Discussion

Try log cabin chinking.

Air sealing a wall like this must be done with a vapor diffusive material or you will get spalled stone faces from sealing materials holding water. I recommend mixing hydrated lime with local clay soils, this is the way they have been sealed for millenia. Vapor open and beautiful. Do not use cement based products to fill the gaps as these are not vapor diffusive.

I've drilled wood window and door jambs on double wythe brick walls and then dense packed.  Helped a lot.  Dunno if that applies to your job.

Lots of interesting ideas.  Typically in the North East we would have just skinned stone on a masonry wall. You could mortar the joints. Obviously you could seal it an close it.  I would seal it with open cell spray foam, Keep the permeability between 3 and 10 perm.  Then air space and interior surface, like green board on steel or timber studs.

I hate to cover it.  The answer for the 100 year old stone foundation in a cheap farm house would be drylock on well prepared surface.

I liked the suggestion to look elsewhere.  You know where the air is coming in, so try to stop the air getting out.  Also, put some nice french doors inside these doors to separate this space from the rest of the house.  Obviously large open vertical columns of air, create their own motivating pressure.  But if you can seal the top, it will slow the infiltration in the bottom. 

RSS

Forum Discussions

How would you insulate this roof?

Started by David Butler in General Forum. Last reply by David Butler 14 hours ago. 15 Replies

Psychrometric Chart Training

Started by John Krochmalny in Training. Last reply by Mahendra Shah 17 hours ago. 1 Reply

Dirty solar panels

Started by Evan Mills in General Forum. Last reply by Stacie Bagnasco on Monday. 1 Reply

Latest Activity

tedkidd replied to Bob Blanchette's discussion Tankless Water Heaters... has their time finally come?
"Yeah. Gas water…"
6 hours ago
Eric Kjelshus replied to Bob Blanchette's discussion Tankless Water Heaters... has their time finally come?
"With super cheap natural gas prices now, still worth going all electric?  Tankless needs a lot…"
7 hours ago
Stuart Langley liked Chris Clay's photo
12 hours ago
David Butler replied to David Butler's discussion How would you insulate this roof?
"Stuart, I wasn't considering the copula windows... yes, those would indeed need to be…"
14 hours ago
Stuart Langley replied to David Butler's discussion How would you insulate this roof?
"Well, @David Butler, you have seen the property more accurately than I have, but my impression of…"
14 hours ago
David Butler replied to David Butler's discussion How would you insulate this roof?
"@ Stuart,I don't think there's any concern about impact of 4" build-up on elevation…"
15 hours ago
Stuart Langley replied to David Butler's discussion How would you insulate this roof?
"So this building has a few issues with air leaks and air leaks have so much to do with discomfort…"
15 hours ago
Stuart Langley replied to David Butler's discussion How would you insulate this roof?
"John Hatfield has the right idea here for a new roof deck. Polyiso boards always need a good stout…"
15 hours ago

Photos

  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service