HELP - AIR SEALING a Continuous Stone Interior/ Exterior Wall

I just recently audited a home that had a blower door number of 11,684 CFM50 and/or 11.81 ACH50. And of course one of the main air infiltration culprits was a stone face wall that was continuous on the outside and inside of the building envelope. The basics as I see it is this: the 1/4" stone joints allow air to freely flow into the house.

Does anyone know of any good methods to seal a high-end stone wall air leakage like this? 

Thanks.

Below are some photos:

PHOTO OF HOUSE Stone Wall Located Bottom Right

CLOSEUP PHOTO OF HOUSE Stone Wall / Back Exterior Door (OUTSIDE)

INFRARED/ ACTUAL Stone Wall/ Back Exterior Door (INSIDE)

INTERIOR WALL - INFRARED / ACTUAL



Views: 4087

Reply to This

Replies to This Discussion

Try log cabin chinking.

Air sealing a wall like this must be done with a vapor diffusive material or you will get spalled stone faces from sealing materials holding water. I recommend mixing hydrated lime with local clay soils, this is the way they have been sealed for millenia. Vapor open and beautiful. Do not use cement based products to fill the gaps as these are not vapor diffusive.

I've drilled wood window and door jambs on double wythe brick walls and then dense packed.  Helped a lot.  Dunno if that applies to your job.

Lots of interesting ideas.  Typically in the North East we would have just skinned stone on a masonry wall. You could mortar the joints. Obviously you could seal it an close it.  I would seal it with open cell spray foam, Keep the permeability between 3 and 10 perm.  Then air space and interior surface, like green board on steel or timber studs.

I hate to cover it.  The answer for the 100 year old stone foundation in a cheap farm house would be drylock on well prepared surface.

I liked the suggestion to look elsewhere.  You know where the air is coming in, so try to stop the air getting out.  Also, put some nice french doors inside these doors to separate this space from the rest of the house.  Obviously large open vertical columns of air, create their own motivating pressure.  But if you can seal the top, it will slow the infiltration in the bottom. 

RSS

Forum Discussions

Speed Tips For Duct Airtightness Testing?

Started by Brendan Reid in General Forum. Last reply by David Butler 1 hour ago. 1 Reply

What made this chimney fall down?

Started by Eric Kjelshus in General Forum. Last reply by Eric Kjelshus on Tuesday. 7 Replies

How would you insulate this roof?

Started by David Butler in General Forum. Last reply by Dave Taylor Nov 11. 61 Replies

Manual J (SD) for custom, luxury homes

Started by Dav Camras in HVAC. Last reply by Dav Camras Nov 10. 3 Replies

Quantitative methods for residential zoning

Started by Brett in HVAC. Last reply by David Butler Nov 9. 1 Reply

Latest Activity

David Butler joined Chris Laumer-Giddens's group
Thumbnail

Energy Efficient Design

Energy efficiency starts at the drafting table...How architects and designers can help buildings…See More
7 minutes ago
David Butler joined James White's group
Thumbnail

Building Simulations

Work collaboratively to find easier, more accurate and better ways to model, predict and verify a…See More
10 minutes ago
David Butler joined Mark Richardson's group
Thumbnail

Renewable Energy

This group will focus on the issues associated with incorporating renewable energy sources like…See More
11 minutes ago
David Butler joined Kyle Brown's group
Thumbnail

Wrightsoft - Manual J / Manual D

If you use Wrightsoft to calculate loads or design ducts, you likely have questions.  Get answers…See More
12 minutes ago
Profile IconDavid Butler and Don Fugler joined Allison A. Bailes III's group
Thumbnail

HVAC

HVAC design, Manuals J, S, T, & D, Duct leakage, Air flow, ENERGY STAR new home requirements,…See More
16 minutes ago
David Butler replied to Brendan Reid's discussion Speed Tips For Duct Airtightness Testing?
"The Home Performance Forum archives include a number of discussions on various methods for sealing…"
1 hour ago
Brendan Reid posted a discussion

Speed Tips For Duct Airtightness Testing?

Anyone like to share their favorite ways to speed up duct airtightness ("Ductblaster") tests?I'm…See More
2 hours ago
Don Fugler added a discussion to the group HVAC
Thumbnail

joining ducts

A question came up on exhaust duct connections. I have always considered screws necessary for…See More
3 hours ago

Photos

  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service