HELP - AIR SEALING a Continuous Stone Interior/ Exterior Wall

I just recently audited a home that had a blower door number of 11,684 CFM50 and/or 11.81 ACH50. And of course one of the main air infiltration culprits was a stone face wall that was continuous on the outside and inside of the building envelope. The basics as I see it is this: the 1/4" stone joints allow air to freely flow into the house.

Does anyone know of any good methods to seal a high-end stone wall air leakage like this? 

Thanks.

Below are some photos:

PHOTO OF HOUSE Stone Wall Located Bottom Right

CLOSEUP PHOTO OF HOUSE Stone Wall / Back Exterior Door (OUTSIDE)

INFRARED/ ACTUAL Stone Wall/ Back Exterior Door (INSIDE)

INTERIOR WALL - INFRARED / ACTUAL



Views: 4088

Reply to This

Replies to This Discussion

Try log cabin chinking.

Air sealing a wall like this must be done with a vapor diffusive material or you will get spalled stone faces from sealing materials holding water. I recommend mixing hydrated lime with local clay soils, this is the way they have been sealed for millenia. Vapor open and beautiful. Do not use cement based products to fill the gaps as these are not vapor diffusive.

I've drilled wood window and door jambs on double wythe brick walls and then dense packed.  Helped a lot.  Dunno if that applies to your job.

Lots of interesting ideas.  Typically in the North East we would have just skinned stone on a masonry wall. You could mortar the joints. Obviously you could seal it an close it.  I would seal it with open cell spray foam, Keep the permeability between 3 and 10 perm.  Then air space and interior surface, like green board on steel or timber studs.

I hate to cover it.  The answer for the 100 year old stone foundation in a cheap farm house would be drylock on well prepared surface.

I liked the suggestion to look elsewhere.  You know where the air is coming in, so try to stop the air getting out.  Also, put some nice french doors inside these doors to separate this space from the rest of the house.  Obviously large open vertical columns of air, create their own motivating pressure.  But if you can seal the top, it will slow the infiltration in the bottom. 

RSS

Latest Activity

Dara Bowser replied to Don Fugler's discussion joining ducts in the group HVAC
"Good to hear you have clean dryer ducts Don. The dryer duct issues that we run into are…"
7 hours ago
Don Fugler replied to Don Fugler's discussion joining ducts in the group HVAC
"David, If the IMC mandates metal dryer duct and prohibits metal screws, they must be accepting…"
8 hours ago
David Butler replied to Don Fugler's discussion joining ducts in the group HVAC
"I never checked that before. Checking now... Section M1502.4.2 of the International Residential…"
9 hours ago
Joseph Frasier is now a member of Home Energy Pros Forum
9 hours ago
Don Fugler replied to Don Fugler's discussion joining ducts in the group HVAC
"Brendan, Thanks for that response. Because of your warning, I just went down to the basement and…"
13 hours ago
Brendan Reid replied to Don Fugler's discussion joining ducts in the group HVAC
"Hi Don, Summary: DRYER VENT: screws bad idea, possibly prohibited by code. METAL DUCT: must be…"
13 hours ago
Profile IconBrendan Reid and David Butler joined Allison A. Bailes III's group
Thumbnail

HVAC

HVAC design, Manuals J, S, T, & D, Duct leakage, Air flow, ENERGY STAR new home requirements,…See More
13 hours ago
Profile IconSean Wiens and David Butler joined Chris Laumer-Giddens's group
Thumbnail

Energy Efficient Design

Energy efficiency starts at the drafting table...How architects and designers can help buildings…See More
21 hours ago

Photos

  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service