Hi All,

I am trying to figure out a good flow grid system to use for testing airflow in 2 to 5 ton forced air systems.

Any favorites?

Or, if you prefer a flow-hood, please tell my why.

The flow hoods I've used take up more space in my vehicle than I would like.

Thanks for your thoughts.

George

Tags: flow, hoods, tools

Views: 202

Reply to This

Replies to This Discussion

I have 3 hoods - low flow ( 10-500 CFM)  Med flow (40-1500 CFM)  high flow (50-2000CFM) Open grid  for kitchen hoods. Plus hot wire plus presser plus other testing tools.   I test the air flow 3 ways  on each major job just to make my point or so I do not mess up.    Flow hoods have been used for 70 years and there's a lot of groups to help get it right.   look at http://www.trutechtools.com ,  www.nationalcomfortinstitute.com,  www.nebb.org,  https://www.aabc.com/www.tabbcertified.org.  I hope this helps some 80% air systems do not have the air flow to keep the unit on high limit.  

Thanks Eric!

Assuming that you're mainly interested in the total air handler flow, and you have access to the filter slots, I'd suggest looking at Energy Conservatory's TrueFlow.  It's a flat plate with openings; it has adapter plates for a variety of filter slot sizes. You'll also need to drill a hole in the supply plenum (or otherwise get a pressure tap in there).

  http://www.energyconservatory.com/products/trueflow%C2%AE-air-handl...

I like the flat true flow plate when it fits-  if not the by pass is very very large.   Or if the presser is to high  its off some.   I have used 4 True flow plates  on a 2 ton spit system to find air flow.    Quick way is just use paper work that comes with the air handler ( you know the knee pad that come with the unit)  find the right unit using the right MO #  then total CFM reading the fan performance data at a constant speed chart.  to find Total SP use your blower door meter with a SP gauge both side of  motor, 3 of 10 will be off with high turbulence.  Have some fun with it and write about it I will be looking for your comments. 

If you wanted more information on the TrueFlow plate, the manufacturer is offering a webinar on it today: https://events-na11.adobeconnect.com/content/connect/c1/1097690081/...

RSS

Forum Discussions

Psychrometric Chart Training

Started by John Krochmalny in Training 5 hours ago. 0 Replies

Too many Heat Pump Water Heaters in a basement?

Started by Brad Cook in General Forum. Last reply by Michael Duclos 10 hours ago. 10 Replies

How would you insulate this roof?

Started by David Butler in General Forum. Last reply by David Butler on Monday. 2 Replies

Dirty solar panels

Started by Evan Mills in General Forum. Last reply by Stacie Bagnasco on Monday. 1 Reply

Latest Activity

B Eric Bell liked Bob Krell's group Healthy Indoors (IAQ)
2 hours ago
John Krochmalny posted a discussion

Psychrometric Chart Training

Looking through the various areas of this site, I didn't see too much information or training on…See More
5 hours ago
Profile IconMike Malek, Avery T. Phillips and Sarah Burger joined Home Energy Pros Forum
6 hours ago
Dannie Jackson's blog post was featured

Core Heat And Other Concepts

  In some places the use of solar heated liquids from hot water solar panels are used to provide…See More
10 hours ago
Michael Duclos replied to Brad Cook's discussion Too many Heat Pump Water Heaters in a basement?
"I’ve been looking into Sanden for a multi-family PH near Laconia, NH, ASHRAE 99.6% temp is…"
10 hours ago
Profile IconTroy Spindler, Mike Berg, Andrew McDowell and 4 more joined Home Energy Pros Forum
yesterday
David Butler replied to Brad Cook's discussion Too many Heat Pump Water Heaters in a basement?
"theoretically, let's say you perfectly isolate the HPWH from a heat source. The HPWH's…"
Monday
David Butler replied to David Butler's discussion How would you insulate this roof?
"Interesting idea. Commercial roof on a slope! Typical density for roofing spray foam is 2.5 to 3.0…"
Monday

Photos

Loading…
  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service