I am trying to quanitfy the energy savings that is generated by having clean furnace filters installed. the furnace filter manufacturers have good data regarding air quality but what does a dirty filter do to the performance of the furnace? 

Views: 556

Reply to This

Replies to This Discussion

To get the conversation going...

Let me start by saying I don't have a complete answer to your question but thought I would throw this out for discussion.

I welcome comments.

 

You can measure the performance difference of the blower between a system with a clean filter and a system with a dirty filter.The measurement will be precise for that one system given those specific filters at that point in time. But it would be hard to apply that to other systems. I don't know if that is of use to you. Also, that is only the blower. I have some thoughts on measuring the rest of the system but they are weak. See below.

 

In order to measure the blower performance you need some way of measuring the energy use of the system.

You could use an Amp meter (Fluke makes a good one) or an energy mgmt device like (e.g. TED  http://www.theenergydetective.com/).

Once you have the energy mgmt device in place, run the system* with the old filter and note the energy use.

Replace the filter and take a new measurement.

Subtracting those two measurements will give you the energy wasted due to the blower.

That should be pretty accurate.

I ran a similar test trying to determine the performance difference with a barometric bypass open vs closed. I ran this test because I suspected the bypass was setup incorrectly and eating to much energy. My test proved my theory with real data.

 

However, you still need to account for the energy wasted from the heating system.

I have no great ideas here but will suggest the following two ideas as a better than nothing solution. I have little confidence of the accuracy of either of these but it might be better than nothing for a ballpark number and it opens up the discussion.

 

1. Use a ratio of the good filter to bad filter energy use and the system rated efficiency to the "bad filter" efficiency.

ex. Blower used 1000 watts with good filter and 1200 watts with bad filter. Furnace is 95% efficient (per mfg).

good filter energy / Bad filter efficiency = good system efficiency /bad system efficiency (BSE)

1000w x 1200 w  = 95% x BSE   or BSE = 88%

 

2. Calculate the additional time that the system has to run due to the inefficiency. Then calculate the fuel cost of that additional time (based on mfg data).

If the system is moving 800 cfm with a clean filter and we calculate the blower is only about 83% efficient  (1000w/1200w), with a dirty filter then the system is pumping 664 cfm. To get the same total volume of air, the system with the dirty filter would need to run 20% more (664cfm x 120% = 800 cfm).

For calculation purposes, let's assume the cost to run the system is $1 per hr per mfg specs, and the system is running 10 hrs per day. It would thus cost an additional 2 hrs and thus $2 per day with the dirty filter.

 

Bonus option: Use both of the above methods and average them out.

 

Paul

RSS

Forum Discussions

How would you insulate this roof?

Started by David Butler in General Forum. Last reply by David Butler 2 hours ago. 15 Replies

Psychrometric Chart Training

Started by John Krochmalny in Training. Last reply by Mahendra Shah 6 hours ago. 1 Reply

Dirty solar panels

Started by Evan Mills in General Forum. Last reply by Stacie Bagnasco on Monday. 1 Reply

Latest Activity

Stuart Langley liked Chris Clay's photo
1 hour ago
David Butler replied to David Butler's discussion How would you insulate this roof?
"Stuart, I wasn't considering the copula windows... yes, those would indeed need to be…"
2 hours ago
Stuart Langley replied to David Butler's discussion How would you insulate this roof?
"Well, @David Butler, you have seen the property more accurately than I have, but my impression of…"
2 hours ago
David Butler replied to David Butler's discussion How would you insulate this roof?
"@ Stuart,I don't think there's any concern about impact of 4" build-up on elevation…"
3 hours ago
Stuart Langley replied to David Butler's discussion How would you insulate this roof?
"So this building has a few issues with air leaks and air leaks have so much to do with discomfort…"
4 hours ago
Stuart Langley replied to David Butler's discussion How would you insulate this roof?
"John Hatfield has the right idea here for a new roof deck. Polyiso boards always need a good stout…"
4 hours ago
Keith Tripp replied to Sean Lintow Sr's discussion Water Saver or Gimmick? in the group Best Practices (Residential)
"Interesting to see that recirc. has been in use for many years in some places. It is still a…"
5 hours ago
Mahendra Shah replied to John Krochmalny's discussion Psychrometric Chart Training
"John Thanks for show and tell tutorial"
6 hours ago

Photos

  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service