I am working on a 1950's colonial with attic insulation consisting of 2"x6" joists filled with loose fill fiberglass. The fiberglass is covered by 1" x 6" decking with 1/4" between the boards. I am recommending adding cellulose to improve the air barrier and insulate. My question is whether I can get away with not removing the old boards, or maybe removing every third one? How much area is needed to ensure moisture can dry to the outside? It should not get damp because of proper ventilation.
The upfront cost of retrofits is a big barrier to comprehensive weatherization. Anything I can do to reduce the cost of installation will help.
Thanks.

Views: 816

Reply to This

Replies to This Discussion

Thanks for asking this question - I've actually been wondering the same thing for personal use. I hadn't thought of the every-third-board idea (seems a good thought), but was instead pondering how far sideways I could shoot sprayfoam (the decking doesn't extend to where the sloped roof gets very low). There's currently ~1" of ancient cellulose in my attic and I'm a total hypocrite for not doing anything about it in the year we've been in the house!

Also need to decide whether or not to shop-vac up the cellulose before sprayfoaming. Thoughts?

Best case is that you remove the boards and the existing insulation completely before doing air sealing--the loose FG has only marginal value, an inch of cellulose almost none. Ideally you are going to install 16-18" of insulation, so the boards will be buried and doing you no good anyway, in the long term.

 

Second best is to carefully move insulation aside so that you can still do a thorough job.

 

If there's a moisture issue, it's probably going to come from air leakage into the attic, not the presence of the boards, so the air sealing is critical. 

Just adding cellulose insulation will not improve your air barrier.  I would recommend removing the floor boards, spot air-sealing with foam (and rigid if necessary) at bypasses, etc. and installing new cellulose or FG.  I would not recommend replacing the boards unless you plan on raising the platform to accommodate adequate insulation.  I discourage attic storage --what's the R-value of a box of christmas ornaments or a suitcase crushing insulation near the platform?

 

Depending on the strength of the ceiling below and no can-lights, etc, you may be able to remove the existing insulation and dense-pack insulation below the boards from the ends or via drilled holes into or removal of certain boards.  You may not achieve enough thickness and I would still be concerned with air and moisture migration since it's not a truly enclosed cavity.

 

If the air barrier is good at the ceiling below (obviously with no can-lights), you could just add more insulation on top of everything.  Seal and bury the ducts as well.  Avoid or replace your knob-n-tube wiring!

This seems to come up often, especially when customers want to keep the floor boards in place for storage.  Best solution would be to remove floor boards, allowing for proper air sealing and achieve a minimum of R-38.  Another option is to remove some boards to air seal, then inject dense pack cellulose.  But, you will only get R-24.  Not so great, and the utilities may not grant you an exception.  Third option, inject foam into cavity (use injection foam and not spray foam). This will take care of air sealing, but again you only get R-30.  Option 3 can also present some IAQ issues.  If it comes into contact with any formaldehyde baring material, the formaldehyde will off-gas.  Injection foam on a flat surface can also warp the material on which it sits.  

 

So, remove the floor boards, do the job right and get rid of the old junk you are trying to store!  IMHO.

In order to do make a substantial difference in the air sealing of your home (this is possible!) you have got to be able to access the ceiling and do some caulking, foaming and rigid batting of air leaks.  While I feel for you and all the work it is going to take in order to remove boards and existing insulation, you will be far ahead by doing so.  My recommendation would be to visit the local temporary labor business in town and get a couple of people to help you for a day.  I imagine you could get some serious work done removing these hindrances in a solid day of work.  No one is going to go back to do air sealing once you have blown additional insulation in your attic.  What you decide now will be there for the next multiple decades.  Bite the bullet!

Your last two statements, "The upfront cost of retrofits is a big barrier to comprehensive weatherization. Anything I can do to reduce the cost of installation will help," are compelling. You need a solution that makes sense, given the conditions.

 

I'd pull up every third or fourth board, as well as the perimeter boards, install baffles, and blow it to r-38 or r-49, infilling where there are voids in the existing fiberglass.

 

Even then, pulling the boards from anywhere but the perimeter may be superfluous. You could blow 16" on top and make sure the ends at the baffles are well-filled. And if the customer insists on retaining some floor space, build a dam around a section and call it good.

 

This may only be an 80% solution, but it may make the difference between an upgrade sold and efficiency gain lost.

 

We need to consider the extent to which some of our austere approaches to home performance scares off our customers, and sends the public a message that our field is unapolegetically fixed and inflexible. We don't have enough credibility among the masses to take that kind of approach. Yet.

RSS

Forum Discussions

Condensation on ceiling and walls of master bedroom

Started by Jerry Needham in General Forum. Last reply by Daniel Baur-McGuire 2 hours ago. 7 Replies

Overheating garage

Started by Chris Bellanca in Best Practices. Last reply by John Nicholas Jul 5. 7 Replies

GSHP for domestic hot water

Started by David Holtzclaw in General Forum. Last reply by Eric Kjelshus Jun 28. 4 Replies

Latest Activity

Franco Oyuela commented on John White's blog post Top 5 Ways to Conserve Energy and Save on Your Air Conditioner Bill
"Summertime, and your air conditioning unit at home will be asked to work super hard in this peak…"
46 minutes ago
Diane Chojnowski's video was featured

The Business of Deep Energy Retrofits

Paul Eldrenkamp has more than 30 years experience in construction and specializes in energy efficiency. In this interview Paul discusses ways to standardize deep energy retrofits. He offers tips for executing projects and managing homeowner…
1 hour ago
Diane Chojnowski posted a video

The Business of Deep Energy Retrofits

Paul Eldrenkamp has more than 30 years experience in construction and specializes in energy efficiency. In this interview Paul discusses ways to standardize ...
1 hour ago
Julie Rosati is now a member of Home Energy Pros Forum
2 hours ago
Daniel Baur-McGuire replied to Jerry Needham's discussion Condensation on ceiling and walls of master bedroom
"Sounds like u opened the hornets nest! I would say a 2600 sq ft home shouldn't need more than…"
2 hours ago
Terry Hill posted an event

Passive House Institute US 2018 Conference at Boston

September 19, 2018 at 6pm to September 23, 2018 at 7pm
Annual conferenceSee More
3 hours ago
John White posted a blog post

Top 5 Ways to Conserve Energy and Save on Your Air Conditioner Bill

Air conditioners are the essential bastions of cool breezes when the mercury skyrockets and the hot…See More
10 hours ago
Jerry Needham replied to Jerry Needham's discussion Condensation on ceiling and walls of master bedroom
yesterday
Gabriel Rojas joined Don Fugler's group
Thumbnail

Kitchen Ventilation

In many homes, cooking is the largest indoor source of air pollutants. Exposures can be higher in…See More
Saturday
Gabriel Rojas joined Bob Krell's group
Thumbnail

Healthy Indoors (IAQ)

The Healthy Indoors group is focused on indoor air quality (IAQ), mold, moisture control, radon,…See More
Saturday
Leslie Jackson commented on David Byrnes's blog post What air conditioner filters work best?
"Hello, Leslie here, with Home Energy magazine. We just got an inquiry from a reader about a DIY air…"
Friday
Profile IconJoe Baumgardner and Steven Grevelis joined Home Energy Pros Forum
Friday
Eric Kjelshus replied to David Butler's discussion another house explodes, killing 2 in apparent natural gas accident
"I have seen dry clay soil let gas though 2-4 blocks away - when wet clay seals the pipe then water…"
Thursday
Kim Krause joined Diane Chojnowski's group
Thumbnail

Job Board

This group is for posting jobs related to all aspects of the home performance industry including…See More
Thursday
Kim Krause liked Diane Chojnowski's group Job Board
Thursday
Horace Douglas Hunt, Jr. joined Bob Krell's group
Thumbnail

Healthy Indoors (IAQ)

The Healthy Indoors group is focused on indoor air quality (IAQ), mold, moisture control, radon,…See More
Thursday
Horace Douglas Hunt, Jr. liked Bob Krell's discussion Join our group discussions on indoor environments
Thursday
Horace Douglas Hunt, Jr. replied to David Butler's discussion another house explodes, killing 2 in apparent natural gas accident
"Prayers for their family. I sure hope it wasnt new appliance. If so, was the installer qualified to…"
Thursday
Elise Brown added a discussion to the group Job Board
Thumbnail

Home Performance Field Technician needed in Midcoast Maine

Join Maine's leading home performance company! Respected, family-friendly company seeks skilled…See More
Thursday
Brett Little's event was featured
Thumbnail

Using the PVwatts Tool for Easy Solar Assessments - Free CE Webinar at Webinar Online

August 22, 2018 from 12pm to 1:15pm
This presentation will include a demonstration of the National Renewable Energy Laboratory's (NREL)…See More
Thursday

Photos

  • Add Photos
  • View All

© 2018   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service