I'm wondering what home performance contractors have found to be the best contract and or pricing method for air sealing duct systems?

What happens when the system has leaky areas that are hard or very difficult to get to and require ripping into walls, etc? One can replace all the ducts and still have inaccessible plenums that leak like sieves.

How do successful contractors protect themselves from systems that have plenums made from framing and one can't get inside to seal them? 

 

Views: 6662

Reply to This

Replies to This Discussion

George, that is a tough question to answer - for most customers they would like a fixed price estimate while some may allow for time & material. No matter which method you choose you need to know all your overhead costs and make sure they are factored in. The protections come not from the type of contract, but the language & limits in them.   

As for tearing into drywall or other portions - if you truly think you need to go that route I would first recommend a full blown Manual J,S,T & D because no one is going to be happy if you seal the ducts, but leave behind some real problems behind that new drywall as the costs for this can easily be in the thousands, if not tens of thousands.

Try setting a time element on each task you perform taping all lines=2 hrs,  mastic on furnace =1 hr etc. Add travel time to and from, setup and cleanup then multiply all hours by the rate you want.

Note: your hourly rate should consider percentages of over head insurance, vehicle, equipment, training etc

Add  mark up on material to your cost. Then add an amount for profit on top of all other costs. Inclued a separate hourly labor rate if you hire help.

Say you need $50 an hour as an initial labor rate for your self to get started. Multiply that by the estimated hours you computed. 10 hrs x $50 = $500 Add materials, disposal of waste to this of say $300= Total estimate of $800.

I always quote the hourly rate for cost over runs, or time and material when you can not give a solid price on areas that may contain hidden costs.

Adjust as necessary as your business  grows.

This is exactly what Aeroseal - aerosol based duct sealing was designed for.  It allows you to seal ducts from the inside, even if they're using building cavities for returns, duct board, etc...  We can not say enough about the product.   We're happy to demo the system for you depending on where you're located.

 

Check out the video on our website for a great overview on Aeroseal - Priority Energy Aeroseal 

 

Regards

And by the way - the process typically prices out at about $1200 - $1,500 to the home owner.  It takes about a day to complete, and there's consumables (sealant, foam, tape, etc...)

In Alabama, feel free to stop by... I know that's way to far,but I would love to see this system work & the duct numbers before & after...

The 1200 to 1500 you list below is easily below what it would cost to rip out drywall & refinish the affected area's in many homes

What are the limits on the size of holes or crack that can be sealed? Thanks

Aeroseal will fill holes up to 5/8"

 

If you're interested I'm sure I can probably find someone in your area

Thanks & yes for a name and number - shoot if it is good as everyone says I might throw my hat in the ring

Sean, The contact info for Aeroseal is as follows.

Aeroseal,LLC

6838 Ellicott Dr.

East syracuse, NY 13057

315-373-0765

I too have been talking with them.

Thanks Ed for the info & now we return this discussion back to the original question.... (maybe)

RSS

Forum Discussions

Too many Heat Pump Water Heaters in a basement?

Started by Brad Cook in General Forum. Last reply by David Butler 18 hours ago. 9 Replies

How would you insulate this roof?

Started by David Butler in General Forum. Last reply by David Butler 19 hours ago. 2 Replies

Dirty solar panels

Started by Evan Mills in General Forum. Last reply by Stacie Bagnasco yesterday. 1 Reply

Fixing a water heater?

Started by John Shillito in Best Practices. Last reply by Eric Kjelshus on Friday. 21 Replies

Latest Activity

Profile IconTroy Spindler, Mike Berg, Andrew McDowell and 4 more joined Home Energy Pros Forum
31 minutes ago
David Butler replied to Brad Cook's discussion Too many Heat Pump Water Heaters in a basement?
"theoretically, let's say you perfectly isolate the HPWH from a heat source. The HPWH's…"
18 hours ago
David Butler replied to David Butler's discussion How would you insulate this roof?
"Interesting idea. Commercial roof on a slope! Typical density for roofing spray foam is 2.5 to 3.0…"
19 hours ago
Summer Redman added a discussion to the group Job Board
Thumbnail

Hiring 2 Training Specialists in Champaign-Urbana, Illinois

The Applied Research Institute (ARI) at the University of Illinois at Urbana-Champaign is seeking…See More
20 hours ago
Summer Redman joined Diane Chojnowski's group
Thumbnail

Job Board

This group is for posting jobs related to all aspects of the home performance industry including…See More
20 hours ago
Profile IconCrystal McLain, Robert Grindrod, Rich Wickman and 3 more joined Home Energy Pros Forum
yesterday
Stacie Bagnasco replied to Evan Mills's discussion Dirty solar panels
"This is a great idea. I clicked on your discussion because it made me remember that I forgot to get…"
yesterday
Kirsten Richnavsky posted an event
Thumbnail

rCloud - The Future of Testing at Your Office or Home

October 18, 2017 from 2pm to 3pm
Integrating rCloud as an essential part of your RESNET QA process.Retrotec’s rCloud app is here,…See More
yesterday

Photos

Loading…
  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service