Dose anyone have experience testing high velocity duct systems?

I've been asked to duct test a Zhender HRV with comfoducts (2" homerun ducts).

I designed & installed a hydronic high velocity system a few years ago. It had 25' of 12" return flex duct, and 15-20' of 6+8" sheet metal ducting, 2 + 2-1/2" branch ducting. I sealed everything with mastic.

I installed the duct tester at the return, and the duct pressure at the nearest supply to the air hander, as I would on a low velocity system. I measured a high duct leakage, I was disappointed. I'm wondering if I should have taken my duct pressure at the supply trunk (6-8") rather than the 2 - 2-1/2" ducts, due to pressure drop.

Any thoughts?

Thanks

 

Views: 459

Reply to This

Replies to This Discussion

This duct system should be tight enough that it should not matter where you test it from.  I recommend you test under negative pressure to ensure you get good seals at the registers.  How high was your reading and what flow range were you on?

When measuring super low flow, do a field check of your duct tester (thank you for not calling it a Blaster) by cutting a 1 inch x 3 inch hole in thick card board and tape it to the flange on your duct tester. This hole should come in at around 16 cfm at 25 Pa with the pressure measured across the cardboard.  If it measures more than that, your duct testing system could be leaking or out of whack some how. 

if the duct leakage is relatively low, 200 cfm or less, the pressure in the duct system will be quite uniform and either location will give consistent results.  If the duct leakage is high, over 500 cfm, we recommend that you do two tests.  One with the probe in the supply register closest to the Duct Blaster setup and one with it in the farthest supply register and average the readings.  

RSS

Forum Discussions

New(ish) ZNE publications available

Started by Ann Edminster in General Forum. Last reply by Jacob Corvidae 14 hours ago. 1 Reply

Energy OutWest 2020

Started by Diane Deyerler in General Forum 16 hours ago. 0 Replies

Proper means of insulating raised floor above concrete

Started by Matthew Greenawalt in General Forum. Last reply by Franco Oyuela on Tuesday. 6 Replies

The Nest Learning Thermostat - Good or Not So Much?

Started by Melissa Baldridge in General Forum. Last reply by Franco Oyuela on Monday. 67 Replies

Latest Activity

Coby Rudolph commented on Jim Gunshinan's blog post What Are the Nation's Best Utility Energy Efficiency Programs?
"Interesting. Something needs to change when 30% of the exemplary programs (16 out of 53) saw…"
12 hours ago
Dimitri Mal joined Bob Krell's group
Thumbnail

Healthy Indoors (IAQ)

The Healthy Indoors group is focused on indoor air quality (IAQ), mold, moisture control, radon,…See More
13 hours ago
Dimitri Mal joined allen p tanner's group
Thumbnail

Energy Auditing Equipment for Sale, Trade or to Purchase

Discuss the pros and cons of the equipment you are interested in prior to purchase. Post equipment…See More
13 hours ago
Jacob Corvidae replied to Ann Edminster's discussion New(ish) ZNE publications available
"Great to see these Ann. Thanks for sharing. "
14 hours ago
Jacob Corvidae commented on Pearl Certification's blog post New Study Measures Impact of Energy Efficient Features On Home Sale Prices in Phoenix
"Congrats folks - great to see that moving forward. We'll look forward to the…"
14 hours ago
tedkidd commented on Jim Gunshinan's blog post What Are the Nation's Best Utility Energy Efficiency Programs?
"Midwest energy is the only program I've run across that's worth a damn. VT and Austin…"
14 hours ago
Jan Green commented on Pearl Certification's blog post New Study Measures Impact of Energy Efficient Features On Home Sale Prices in Phoenix
"The link to the study doesn't work. "
15 hours ago
Jan Green commented on Pearl Certification's blog post New Study Measures Impact of Energy Efficient Features On Home Sale Prices in Phoenix
"Excellent forward thinking partnership.  Gaining momentum with this partnership is HUGE!…"
15 hours ago

© 2019   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service