Does IRC preclude use of spray foam to insulate rim bands in unfinished basement? (re: ignition barrier)

My new home, currently under construction, has a full basement, half of which will remain unfinished, i.e., no drywall or ceilings. We intend to use that area for storage. My specs call for 2" foil-faced polyiso on the walls (below grade) and 6" oc-SPF in the rim band area (mostly above grade). Spraying the rim band is obviously a LOT easier than cutting & piecing foam board between the floor trusses and over the double end pins.

Since there's no ceiling, an alternate thermal and ignition barrier is required in the unfinished area. It's clear from the code and spray foam ESR reports that an approved intumescent coating satisfies the thermal barrier requirement. However, the same does not appear to be the case for the ignition barrier requirement.

In particular, the ESR reports for the products being considered only address the use of an alternative ignition barrier (i.e., coating) in crawl spaces (or attics) with service access only (i.e., 'no storage is permitted'). Also, the air in that area cannot be circulated to other parts of the building."  My HVAC design calls for return air to pass through the basement, including unfinished area.

If I want to keep this area unfinished (omitting the ceiling greatly facilitates future access to pipes, wires, dampers, etc), it seems I have two choices: either cover the spray foam with an approved material such as hardboard (re: R316.5.4.3) or cut-and-piece foil-faced polyiso into the rim band. Either option would be a pain in the butt.  I checked the ESR's for several different SPF products and all have the same limitations where there's no prescriptive ignition barrier.

Am I interpreting the ignition barrier requirements correctly?


Views: 147

Reply to This

Replies to This Discussion

Depending on the type of floor joists you may already be required to cover the floor joists.  There are spray-on ignition barriers as well.

R316.5.11 says not more than 3-1/4 inches of certain density foam and some other verbiage need not be covered in the perimeter joist space.

use a spray foam that is approved as an ignition barrier … and while you are at it use a foam that has low Global Warming Potential, something like ; that's not an endorsement but an example. There is probably a thickness limit to the amount of foam that is approved for, maybe 4" in that products case but if you use closed cell that's plenty of r-value for rimjoist.

If you are up against a thickness limit then you can always add rock wool or equivalent to boost your r-value.

I also believe that the exception Peter refers to in R316.5.11 is an exception to the thermal barrier requirement. So if you don't meet those criteria for an exception (thickness of foam, density, or flame spread) then you just install the thermal barrier and you meet code so that would be acceptable in your example. Of course, I'm not your fire code official (or anyone's) so that is who knows for sure.

I also thought the Section R316.5.11 exception only applied to the thermal barrier requirement. After all, it specifically refers to the thermal barrier.  But as it turns out, I was confused about the relationship between thermal and ignition barriers. As it turns out, I was asking the wrong question. Allow me to explain...

I spoke with a senior technical rep at one of the foam mfrs whose job it is to know these things. He pointed out that the requirements I'm hung up on when using an intumescent coating as an ignition barrier (as described in his product's evaluation report) were specifically referring to spaces that are isolated from living space (i.e., attics & crawlspaces) and thus don't require a thermal barrier.

He explained that a thermal barrier is a higher hurdle than an ignition barrier (someone reading the evaluation report is presumed to know this). This relationship is evidenced by the intumescent coating thickness required to satisfy the former vs. the latter. Ignition barriers only come into play in isolated spaces where there's no requirement for a thermal barrier. In a non-isolated space such as my unfinished basement, I *must* have a thermal barrier, so I can ignore the ignition barrier requirements.

Bottom line, I can specify 6 inches of oc-SPF with an approved coating at a thickness that satisfies the thermal barrier requirement, which I already knew I could do.  OR, I can use the R316.5.16 exception and not apply a coating as long as I don't exceed the 3-1/4-inch depth limitation. In that case, I would need to use 2 lb foam to achieve my design R-value for the rim band. So it becomes a cost trade at that point, which only my installer can answer.

Thanks for the replies!


Latest Activity

Pearl Certification posted a blog post

New Study Measures Impact of Energy Efficient Features On Home Sale Prices in Phoenix

City of Phoenix, APS and RESNET Join Pearl Certification and HomeSmart In Launching Innovative Home…See More
4 hours ago
Amber Vignieri posted a blog post

New Video Explains the Super Stars of Energy Efficiency: Air Sealing and Insulation

Air sealing and insulation are the celebrities of the high-performance home world (high performance…See More
4 hours ago
Brett Little posted an event

The Smart Enclosure System: Building in the Anthropocene - Free CE Webinar at Webinar Online

January 23, 2019 from 12pm to 1:15pm
The Smart Enclosure System offers a 21st-century guide to advanced high-performance building…See More
5 hours ago
Franco Oyuela replied to Matthew Greenawalt's discussion Proper means of insulating raised floor above concrete
"Proper insulation methods. Blanket: Batt and Roll InsulationFiberglass Batt Insulation…"
6 hours ago
Profile IconAnn McCartan, Dimitri Mal, Richard Barlow and 3 more joined Home Energy Pros Forum
9 hours ago
Luke Langhals replied to Don Fugler's discussion Depressurization/make-up air issues in the group Kitchen Ventilation
"I've seen both work with success, really it comes down to duct design/placement. It would…"
11 hours ago
Diane Chojnowski posted an event

EEBA: High Performance Home Summit at San Diego

October 16, 2019 to October 18, 2019
Join us in sunny San Diego, October 16-18, at the MUST-ATTEND event of the year for builders,…See More
11 hours ago
Ryan Miller's event was featured

Crawl Space Encapsulation Specialist Training at Raleigh, NC

March 19, 2019 at 9am to March 20, 2019 at 5pm
Looking to improve your crawl space encapsulation knowledge?  Join us on March 19 – 20 in Raleigh…See More
11 hours ago

© 2019   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service