I wanted to know if anyone had any experiences using the bubble wrap w/ the double sided radiant barrier.

I had a weird experience thanks to a fire pit, my Brother-in-Law, and a few beers.  My Brother-in-Law made a make shift pot holder looking glove and held it about 8" away from a pile of extremely hot embers.  After nearly a minute the glove started to smoke because the exterior nearest the fire was starting to melt.  Despite this, he said the inside never got that hot.

What I am figuring is that, if this material works this well with such extreme temperatures, why wouldn't it be useful in a knee wall area?  It would be a lot easier to install than rigid foam board and much easier to squeeze through a small access hole.

 

What do you guys think?  Do you have experience using this material? (Keep in mind I live in Atlanta, GA, not New England).  Thanks!

Tags: Insulation, bubble, heat, knee, transfer, walls, wrap

Views: 1109

Reply to This

Replies to This Discussion

Remember, a radiant barrier only reflects radiant heat.  The fire test your brother in law did was the ideal test for that material, since essentially all the heat was radiant, but in an attic situation that's not the case.  For the radiant barrier to work, there has to be an air space between the barrier and any other objects (to rule out conduction), and its surface has to remain clean and shiny (no dust collection).  So would it help in a kneewall area?  Maybe a little, but not as a replacement for insulation.
I get your point, but I am talking about using it in addition to the existing insulation.  The most common treatment here for knee wall problems is to seal the penetrations from the attic side of the wall, push the batts (usually R-13 here) back into place and then attach Thermax sheathing with a radiant barrier to the studs over the batts and seal the seams. Sometimes the construction, access, and penetrations make using a rigid foam board product very difficult to use. The bubble wrap radiant barrier seems to be a good alternative.

Installed in that location -- over the fiberglass batts -- I would be concerned about condensation on the bottom surface wicking into the fiberglass and creating mold habitat.  I'd also be concerned that dust would accumulate on the top surface and make the radiant properties useless. 

Has this stuff been in use long enough to be able to check in on an installation that's 5 or 10 years old to see how it's holding up?

Jon,

 

  I'm guessing that the foil/bubble wrap will provide a real good air seal if installed properly (like every other air seal material) but will be much more costly than poly wrap and not provide anywhere near the insulation of EPS or XPS board.  I've seen no independent testing of these products to verify their claimed "R" values.  Knee walls are always a pain; almost makes you want to rip out the walls to re-do everything.

You can say that again.
We see Reflectix used behind knee walls all the time.  It is the air barrier to prevent windwashing, and meets code for fiberglass batt covering.

You should put a link to Reflectix in your post. I haven't heard of it.

RSS

Forum Discussions

How would you insulate this roof?

Started by David Butler in General Forum. Last reply by David Butler yesterday. 15 Replies

Psychrometric Chart Training

Started by John Krochmalny in Training. Last reply by Mahendra Shah yesterday. 1 Reply

Dirty solar panels

Started by Evan Mills in General Forum. Last reply by Stacie Bagnasco on Monday. 1 Reply

Latest Activity

tedkidd replied to Bob Blanchette's discussion Tankless Water Heaters... has their time finally come?
"Yeah. Gas water…"
yesterday
Eric Kjelshus replied to Bob Blanchette's discussion Tankless Water Heaters... has their time finally come?
"With super cheap natural gas prices now, still worth going all electric?  Tankless needs a lot…"
yesterday
Stuart Langley liked Chris Clay's photo
yesterday
David Butler replied to David Butler's discussion How would you insulate this roof?
"Stuart, I wasn't considering the copula windows... yes, those would indeed need to be…"
yesterday
Stuart Langley replied to David Butler's discussion How would you insulate this roof?
"Well, @David Butler, you have seen the property more accurately than I have, but my impression of…"
yesterday
David Butler replied to David Butler's discussion How would you insulate this roof?
"@ Stuart,I don't think there's any concern about impact of 4" build-up on elevation…"
yesterday
Stuart Langley replied to David Butler's discussion How would you insulate this roof?
"So this building has a few issues with air leaks and air leaks have so much to do with discomfort…"
yesterday
Stuart Langley replied to David Butler's discussion How would you insulate this roof?
"John Hatfield has the right idea here for a new roof deck. Polyiso boards always need a good stout…"
yesterday

Photos

  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service