I just found a neighborhood of this stuff, degraded to a fine powder, can be disturbed by BD, This foam (back East) was urea/formaldehyde based and sometimes toxic.  We're not using BD until I have the stuff tested.  Anyone know about best practices or protocols for dealing with this?

Views: 2214

Reply to This

Replies to This Discussion

Oh no it was used country wide & if worried I would not depressurize the house & instead opt to pressurize it if you really need the numbers to start. (I could have sworn that was all handled under a class suit, but that could be something else) I would recomend going with a dense pack cellulose, but before blowing it in, see if they can use that hole to vacuum the bulk out.

By the way, BD= Blower Door. And the dust is incredibly fine, offering no resistance to a probe.  We are having it tested and doing some thermal imaging now that we have winter (ish) conditions in north central Nebraska.

Sean's suggestion is to turn the fan around. If the material is friable it won't be pulled into the house.

Barring some huge kitchen vent you are likely to get a very similar CFM50 number. 

Here's a quote and link from the EPA.  There is also good info on the InspectAPedia web site, including pictures. Look it up under UFFI (Urea Formaldehyde Foam Insulation)

"During the 1970s, many homeowners had urea-formaldehyde foam insulation (UFFI) installed in the wall cavities of their homes as an energy conservation measure. However, many of these homes were found to have relatively high indoor concentrations of formaldehyde soon after the UFFI installation. Few homes are now being insulated with this product. Studies show that formaldehyde emissions from UFFI decline with time; therefore, homes in which UFFI was installed many years ago are unlikely to have high levels of formaldehyde now."

http://www.epa.gov/iaq/formaldehyde.html

We replaced a ceiling in a room during a reno project for a customer recently and found it in the sidewalls of this old two story.  There were a lot of voids and gaps and it was very powdery when touched.

Looking back (20/20 hindsight) the issue looks kind of silly. "Let's tighten the snot out of buildings and walk away - what could go wrong?" 

ACH goes way down, moisture goes way up, every piece of furniture and flooring starts off gassing to beat the band, and it all stays nicely contained. 

I suspect if they'd installed mechanical ventilation/had todays requirements those homes might not have had problematic IAQ issues.  

What did you find about the dust? 

RSS

Latest Activity

Profile IconLauren Asplen and Danny Gough joined Bob Krell's group
Thumbnail

Healthy Indoors (IAQ)

The Healthy Indoors group is focused on indoor air quality (IAQ), mold, moisture control, radon,…See More
6 hours ago
Franco Oyuela commented on John White's blog post What to Expect from a New HVAC Unit Installation Cost
"Is strongly advise against attempting to install any complex home comfort equipment on your own.…"
7 hours ago
CEE posted a blog post
8 hours ago
Lindsay Bachman liked David Keefe's video
8 hours ago
Julie Saporito's blog post was featured
9 hours ago
John C. Semmelhack liked Diane Chojnowski's discussion Everything you need to know about California's new solar roof mandate
10 hours ago
Profile IconJohn Walter and Eric Rabesa joined Home Energy Pros Forum
23 hours ago
William Collins posted a video

The Foam Sealants Kit " Bead or Spray"

Now you can apply foam sealant as a " bead " or a " spray " with the Foam Sealants Kit. When using a 16lb Canister of Black Sealant you can easily go from us...
yesterday
Profile IconSean Wiens and Armando Cobo joined Don Fugler's group
Thumbnail

Kitchen Ventilation

In many homes, cooking is the largest indoor source of air pollutants. Exposures can be higher in…See More
yesterday
Julie Saporito posted a blog post
yesterday
Brennan Less replied to Linda Wigington's discussion Good Eating with Reduced Cooking Emissions in the group Kitchen Ventilation
"Cook outside, as much as you can, and close your doors/windows while you do it ;) "
yesterday
Ethan Foley joined Bob Krell's group
Thumbnail

Healthy Indoors (IAQ)

The Healthy Indoors group is focused on indoor air quality (IAQ), mold, moisture control, radon,…See More
yesterday
Shane S posted a photo
yesterday
Al Tibbs posted photos
Wednesday
Al Tibbs commented on Eric Aune's photo
Thumbnail

IMG00173-20100805-1030

"Always remind customer to make sure to mark out location of piping before covering!! The infrared…"
Wednesday
Al Tibbs commented on Eric Aune's photo
Wednesday
Joe is now a member of Home Energy Pros Forum
Wednesday
Liam Smith replied to Silas Inman's discussion Best Energy Myths
"Yes incandescent bulb are very heat productive. Instead of that use LED bulb which are energy…"
Wednesday
Kelly Vaughn's blog post was featured

How Cities Can Ensure Better Rentals for Everyone

By Alisa PetersenWhile much of RMI’s research and analysis on home energy performance has focused…See More
Wednesday
Brett Little's event was featured

Resilient Design in an Age of Climate Change - Free CE Webinar at Webinar Online

May 30, 2018 from 12pm to 1:15pm
A changing climate, sea level rise, drought, and a wide range of stresses in the world are…See More
Wednesday

Photos

  • Add Photos
  • View All

© 2018   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service