Airflow "through" a building or "beneath" the exterior cladding

As a licensed home inspector in the southeast, I have observed residential structures (typically 15 - 25 years old) clad with vinyl lap siding that have particulate matter deposited at some of the overlapping seams of the siding (see photos). This is typically observed on one side - presumably the leeward side.

I've been of the impression that these “puff-like” markings are likely the result of dirt depositing on the siding from the movement of air in the space behind the siding due to changes in air-pressure on the building shell. When the wind blows on one side of a home and it creates a positive pressure on that windward side, the resulting negative pressure on the opposite (leeward) side “pulls” at the siding and the air behind the siding rushes out to fill the (pressure) void, bringing out any underlying particulate which may then deposit on the siding.

But I've secretly worried that this could instead represent airflow "through" the building envelope and not around it.

I've just recently observed this same phenomenon on a home constructed in 2012 with fiber-cement lap siding (with flashing at field butt-joints) that I believe was sheathed with the (Huber) ZIP System (additional photo). Done right, the taped seams of the Zip System create a reasonably tight air barrier.

I have consulted with 3 - 4 manufacturer's of fiber-cement siding hoping that they may have had a warranty claim on the issue (knowing full well it isn't a product defect), and could they offer insight as to the cause and/or cure. To no avail.

Am I on the right track, especially with this newer case of a home that I believe to be reasonably tight beneath the cladding? Is this occurring within the interstitial space between the backside of the siding and the exterior of the sheathing, then moving around the sides of the building and out the leeward side? Or could this possibly be representative of airflow through the building envelope and therefore represent more of an energy and IAQ concern for the occupants?

I'm also curious why, for the fiber-cement siding, the airflow seems to expel along the bottom edge of a course of siding specifically at the location of the (flashed) butt joint of the course below - why not along the entire span? The airflow is not expelling from the butt joint (based upon the pattern), unlike the vinyl siding, where the airflow appears to come through the overlap of successive side-by-side sections of siding.

Are their solutions to prevent this mostly cosmetic outcome?

Tags: Airflow, Building, Envelope

Views: 423

Attachments:

Reply to This

Replies to This Discussion

Interesting observation. It sounds like your a good Home inspector.

It seems to me like the air movement is the  from the latter. The air is moving through the wall assembly caused by the Delta-P, and it is showing up where the leaks are located in the wall  assembly.

As far as a solution, I think it would depend on how much the homeowner wishes to pay (as usual). I would recommend pressuring the building with a Blower door and then scan with an IR camera to see for certain what the cause actually is, and then come up with a workscope. It may be that a more invasive evaluation may be needed, and that's where the added cost will determine what measures the homeowner is willing to take on.

I also wouldn't expect that newer houses are tighter unless they are Energy Star, and I see no claim under a warranty from a manufacture. I'm also surprised about the Zip System, they are usually somewhat effective and installed by contractors who understand its purpose.

The last picture with fiber cement - looks like the pattern you might see from water.

Is the fiber cement board on firring?  Blind nailing?  Did they paint the fiber board after installation and seal up the overlapping --- leaving only the end gaps for air to escape?  In general the manufacturers also recommend air gap at the bottom of the wall and the top of the wall for air circulation from bottom up... is that missing?

The purpose of the siding --- especially if it has firring behind it -- is a rain screen and  wind screen.  Hopefully the builder used other techniques to provide the air tightness.  Assuming that they did - air moving under the siding, round the outside of the building as wind blows is not really likely to cause a problem - provided the backsides of the siding was primed.  Installed as per manufacturer's instruction it shouldn't be a problem.

Did you do a blower door test?

The seams will also exhibit a capillary effect and hold moisture by them longer... which could help build up dirt. The horizontal pattern may be caused in part by moisture flowing along the seams when it rains...  what kind of climate is this in?


Looking at the first two pictures - that really looks like a pattern you might get from dirt collecting on the outside of a surface as its drying... with wind blowing mostly from one direction. The air will cling to the siding surface and at the joint there will be a slight increase in turbulence. It simply may leave that area wetter longer and allow for the dirt to cling to it and start building up. Look at the bottom of the joints - you can see a clear air gap on the bottom side and you don't see a dirt pattern coming from that air gap. But it does look like the edge of the sideing as the water would flow over it is dirtier... this looks like a normal build up of dirt in a climate that has some rain. With winds that blow frequently from one direction?

Just thinking.... out loud...

I'm suspecting the dust gets into the attic at the eaves where the largest pressure diff's are from the wind, from there down the wall outside the vapor barrier pumped through by gusts.

The barrier job sounds too worthy for blow-through to me and via the attic is something to check when you get dust in homes. I lived with strong winds in Phoenix & saw the attic as the usual source, having it exit under the siding is weird but the winds are really strong at times over the roof for pressure.

RSS

Forum Discussions

Overheating garage

Started by Chris Bellanca in Best Practices 1 hour ago. 0 Replies

GSHP for domestic hot water

Started by David Holtzclaw in General Forum. Last reply by David Holtzclaw 4 hours ago. 3 Replies

Log home roof insulation

Started by Bob Reuther in Best Practices. Last reply by Daniel Baur-McGuire yesterday. 8 Replies

Latest Activity

Chris Bellanca posted a discussion

Overheating garage

Hi all, I'm looking for potential solutions to a problem at a client's house.  The south facing 2…See More
1 hour ago
Landon added a discussion to the group Energy Auditing Equipment for Sale, Trade or to Purchase
Thumbnail

Brand new retrotec blower door system $3000

Hi, I’ve got a brand new blower door system from retrotec that I got 2 months ago, and never got…See More
1 hour ago
John Redmond posted discussions
1 hour ago
David Holtzclaw replied to David Holtzclaw's discussion GSHP for domestic hot water
"Thanks John & Bill. Bill your experience is one reason why I wanted a larger heat pump with…"
4 hours ago
John White posted photos
13 hours ago
Diane Chojnowski posted events
yesterday
Rob commented on Bob Krell's group Healthy Indoors (IAQ)
"Hello, Has anyone tried custom filtering of window AC units? Specifically concerned with…"
yesterday
Michael Dunseith's 2 photos were featured
yesterday
Franco Oyuela commented on Perry Ning's blog post Warnings About Portable Air Conditioners
"Here are the top five benefits of owning a portable air conditioner: 1. Low Price – All…"
yesterday
Daniel Baur-McGuire commented on Kurt Shafer's status
"Whole house fans are a scam if you use air conditioning. Seriously "
yesterday
Daniel Baur-McGuire commented on Michael Dunseith's photo
Thumbnail

NYC DEPT OF BUILDINGS TR8 ENVELOPE TESTING

"Looks fun. How did you connect all the fans together or did you adjust the flows manually? The…"
yesterday
Daniel Baur-McGuire replied to Bob Reuther's discussion log home roof insulation
"I would look to stop air from penetrating the ceiling. I would guess hot air is able to rise…"
yesterday
Jay Lillien posted a blog post

How Changing Temps Affect Your Home’s Windows

In Colorado, there’s a time-honored saying:“If you don’t like the weather, just wait a few minutes……See More
Tuesday
Matt Peiris replied to H.O. Electric's discussion Stop Drinking Bottled Water! in the group News & Announcements
"Cities like Los Angeles now use chlorine AND chloramine to treat their water. While chlorine can be…"
Tuesday
Matt Peiris joined Diane Chojnowski's group
Thumbnail

News & Announcements

Share your news and announcements with the community in this group.To post news or an announcement,…See More
Tuesday
Michael Dunseith posted photos
Tuesday
Ron Jones added a discussion to the group Job Board
Thumbnail

Residential Construction Superintendent for Net Zero Energy Homes: Northern California

At Acre Designs (acre.co), we're bringing Net Zero Energy homes into the 21st century, and we're…See More
Monday
Kim added a discussion to the group Job Board
Thumbnail

Job Opening - New Construction Specialist - Philadelphia or Pittsburgh, PA Location

New Construction SpecialistAre you looking for a collaborative work environment, colleagues who are…See More
Monday
Profile IconSteve, Todd Crawford and Evangeline Spence joined Home Energy Pros Forum
Monday
Steve liked Alex Jonson's discussion Constant Airflow Regulator
Monday

Photos

  • Add Photos
  • View All

© 2018   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service