I'm looking to find a Good template to make up some labels to comply with this:

 

401.3 Certificate. A permanent certificate shall be posted on or
in the electrical distribution panel. The certificate shall not cover
or obstruct the visibility of the circuit directory label, service disconnect
label or other required labels. The certificate shall be
completed by the builder or registered design professional. The
certificate shall list the predominant R-values of insulation
installed in or on ceiling/roof, walls, foundation (slab, basement
wall, crawlspace wall and/or floor) and ducts outside conditioned
spaces; U-factors for fenestration and the solar heat gain
coefficient (SHGC) of fenestration. Where there is more than one
value for each component, the certificate shall list the value covering
the largest area. The certificate shall list the types and efficiencies
of heating, cooling and service water heating equipment.
Where a gas-fired unvented room heater, electric furnace, or baseboard
electric heater is installed in the residence, the certificate
shall list “gas-fired unvented room heater,” “electric furnace” or
“baseboard electric heater,” as appropriate.An efficiency shall not
be listed for gas-fired unvented

 

The Code in our area mandates this.  Does anyone have something they would be willing to share?

 

Thanks

Views: 2763

Reply to This

Replies to This Discussion

Thanks Dave, looks very good. 

I notice in Supplement B5 they use the 50 pascal benchmark but the sticker uses 25 pascals.  Why the disconnect?

As far as I know, all blower door is 50, duct is 25, and if you were doing duct to outside they'd both be 25.
Definitely will teach me to not read without the glasses!

RSS

Forum Discussions

Too many Heat Pump Water Heaters in a basement?

Started by Brad Cook in General Forum. Last reply by David Butler 20 hours ago. 9 Replies

How would you insulate this roof?

Started by David Butler in General Forum. Last reply by David Butler 21 hours ago. 2 Replies

Dirty solar panels

Started by Evan Mills in General Forum. Last reply by Stacie Bagnasco yesterday. 1 Reply

Fixing a water heater?

Started by John Shillito in Best Practices. Last reply by Eric Kjelshus on Friday. 21 Replies

Latest Activity

Profile IconTroy Spindler, Mike Berg, Andrew McDowell and 4 more joined Home Energy Pros Forum
2 hours ago
David Butler replied to Brad Cook's discussion Too many Heat Pump Water Heaters in a basement?
"theoretically, let's say you perfectly isolate the HPWH from a heat source. The HPWH's…"
20 hours ago
David Butler replied to David Butler's discussion How would you insulate this roof?
"Interesting idea. Commercial roof on a slope! Typical density for roofing spray foam is 2.5 to 3.0…"
21 hours ago
Summer Redman added a discussion to the group Job Board
Thumbnail

Hiring 2 Training Specialists in Champaign-Urbana, Illinois

The Applied Research Institute (ARI) at the University of Illinois at Urbana-Champaign is seeking…See More
22 hours ago
Summer Redman joined Diane Chojnowski's group
Thumbnail

Job Board

This group is for posting jobs related to all aspects of the home performance industry including…See More
22 hours ago
Profile IconCrystal McLain, Robert Grindrod, Rich Wickman and 3 more joined Home Energy Pros Forum
yesterday
Stacie Bagnasco replied to Evan Mills's discussion Dirty solar panels
"This is a great idea. I clicked on your discussion because it made me remember that I forgot to get…"
yesterday
Kirsten Richnavsky posted an event
Thumbnail

rCloud - The Future of Testing at Your Office or Home

October 18, 2017 from 2pm to 3pm
Integrating rCloud as an essential part of your RESNET QA process.Retrotec’s rCloud app is here,…See More
yesterday

Photos

Loading…
  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service