Chris Peters's Discussions (9)

Discussions Replied To (9) Replies Latest Activity

"I just looked at the specs. What I couldn't determine was the draft measure incremen…"

Chris Peters replied Nov 8, 2013 to Combined combustion tester CO + Manometer

2 Nov 15, 2013
Reply by Eric Kjelshus

"I will second that motion. Who can do it? Consumer Reports?"

Chris Peters replied Apr 4, 2011 to Energy Modeling Software - what works??

48 Feb 23, 2012
Reply by Jim Baerg

"There isn't one that I know of. I built one for personal use. It has initially the B…"

Chris Peters replied Mar 31, 2011 to Let's hear your feedback on Home Energy Pros!

31 Jun 15, 2015
Reply by Andrew J. Courts, Jr.

"Eric, I am BA, Envelope and Heating BPI Certified. I have quite a bit of experience…"

Chris Peters replied Mar 14, 2011 to Drilling through a flue pipe of a power-vented combustion appliance

17 Mar 14, 2011
Reply by David Meiland

"You're very welcome."

Chris Peters replied Mar 12, 2011 to Where to install the vapor barrier for a finished basement?

11 Mar 9
Reply by David Eakin

"I'm referencing Joe Lstiburk's "Cold Climates" You should not install poly on the wa…"

Chris Peters replied Mar 11, 2011 to Where to install the vapor barrier for a finished basement?

11 Mar 9
Reply by David Eakin

"I guess I can't see why one cannot go outside and test at the vent terminal. Then th…"

Chris Peters replied Mar 11, 2011 to Drilling through a flue pipe of a power-vented combustion appliance

17 Mar 14, 2011
Reply by David Meiland

"I have to disagree with you on using those plugs. Cat IV PVC flues are pressurized a…"

Chris Peters replied Mar 10, 2011 to Drilling through a flue pipe of a power-vented combustion appliance

17 Mar 14, 2011
Reply by David Meiland

"Blaine, you beat me to it. There is a huge difference between a positive pressure Ca…"

Chris Peters replied Mar 4, 2011 to Drilling through a flue pipe of a power-vented combustion appliance

17 Mar 14, 2011
Reply by David Meiland

RSS

Forum Discussions

Latest Activity

David Butler replied to Dav Camras's discussion Experience with new energy monitoring tools such as Curb, Sense, Nerio and Smapee
"Steve, my understanding from having followed NILM research in years past is that the monitoring…"
6 hours ago
David Butler commented on Blake Reid's blog post Heating Houses in Hawaii (pt. 1)
"I haven't used Treat but if it has a Design Heating and Cooling load report, I'm sure…"
7 hours ago
Profile IconScott Morehouse and Dana Fischer joined Home Energy Pros Forum
13 hours ago
Steve Schmidt replied to Dav Camras's discussion Experience with new energy monitoring tools such as Curb, Sense, Nerio and Smapee
"Like Dan I've had my Sense installed for about a year and so far it has not lived up to the…"
13 hours ago
Blake Reid commented on Blake Reid's blog post Heating Houses in Hawaii (pt. 1)
"David, you've found my problem.  How to find good inputs, still use some…"
14 hours ago
David Butler replied to Dav Camras's discussion Experience with new energy monitoring tools such as Curb, Sense, Nerio and Smapee
"re: Scott's comment about The Energy Detective monitoring individual appliances... TED uses a…"
14 hours ago
David Butler commented on Blake Reid's blog post Heating Houses in Hawaii (pt. 1)
"What software are you using? Proper heat load calculations are based on the local Design…"
14 hours ago
Mick Lane liked Dav Camras's discussion Experience with new energy monitoring tools such as Curb, Sense, Nerio and Smapee
15 hours ago

Photos

  • Add Photos
  • View All

© 2017   Created by Home Performance Coalition (HPC)   Powered by

Badges  |  Report an Issue  |  Terms of Service